Miele CS 1028 Operating And Installation Instructions
Gas combiset
Hide thumbs
Also See for CS 1028:
- Operating and installation instructions (56 pages) ,
- Converting instructions (40 pages) ,
- Operating and installation instructions (44 pages)
Related Manuals for Miele CS 1028
Summary of Contents for Miele CS 1028
- Page 1 Operating and Installation Instructions Gas Combiset CS 1028 ® ® en - US, CA To prevent accidents and appliance damage, read these instructions before installation or use. M.-Nr. 07 369 720...
- Page 2 WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. – Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
-
Page 3: Table Of Contents
Turning on and off / Regulating ........12 Using the cooktop during a power failure ....... 13 Pans . -
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS WARNING- When using your gas appliance follow basic precautions, including the following: This gas combiset conforms to all uniform safety codes and regulations. Read all instructions before installation or use to prevent injury and appliance damage. Keep these operating instructions in a safe place and pass them on to any future user. - Page 5 Technical safety Installation, repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. Before installing the combiset, check for externally visible damage. Do not operate a damaged appliance.
- Page 6 However, under certain circumstances it may be possible for installation in these applications. Please contact the nearest Miele Dealer or the Miele Technical Service Department with specific requirements. After connecting the appliance test for leaks according to the installation instructions.
- Page 7 Do not use pans that extend past the burner grate. Using larger pans may cause the flames to spread out and damage the surrounding countertop or other countertop appliances. For safety and stability, do not use pans with a bottom diameter smaller than the burner grate.
- Page 8 In the event of damage or defect, turn off the appliance immediately. Turn off the gas shut off valve and disconnect completely from the electrical supply. Contact the Miele Technical Service Department. Do not use the appliance until it has been repaired.
-
Page 9: Guide To The Combiset
Guide to the combiset Burner grate Burner Control knob... -
Page 10: Burner
Guide to the combiset Burner Burner cap Burner head Cover plate Ignitor Ignition safety control (Thermocouple) Burner base... -
Page 11: Before Using The Combiset
Cleaning the combiset Before using for the first time clean the appliance as follows: ^ Remove any protective foil. ^ Wash the removable parts of the gas burner in a mild solution of warm water and liquid dish soap. ^ Dry and reassemble the parts in the correct order (see "Cleaning and care"). -
Page 12: Operation
Operation Turning on and off / Regulating The control knob is used to turn on the burner and to regulate the strength of the flame. ß The gas supply is turned off * Ignition setting & Highest flame / Lowest flame The knob must only be turned left to turn the appliance on and right to turn it off. -
Page 13: Using The Cooktop During A Power Failure
Turning off ^ Turn the control clockwise to "ß". This stops the flow of gas and the flame goes out. Using the cooktop during a power failure If there is an interruption to the electrical supply, the gas can be ignited using a match. -
Page 14: Pans
Pans Pan size – Set the combiset to a high flame when using a large diameter pan and low flame when using a small diameter pan. – Generally, wide / shallow pans will heat faster and cook more evenly than narrow / tall ones. –... -
Page 15: Safety Features
Ignition Safety Control This gas combiset incorporates an Ignition Safety Control which stops the supply of gas if the flame goes out. ^ To reignite the burner, turn the control knob clockwise to “ß”, then turn on the burner as usual. This safety feature is not operated by electricity, it will be active even if the appliance is in use during a power... -
Page 16: Cleaning And Care
Apply sparingly with even pressure. These cleaning products are available from Miele. Do not use stainless steel cleaner on or around the printing, it may rub off. Use only a soft sponge with some dish liquid and warm water to clean this area. -
Page 17: Burner
Burner Do not clean any parts of the burner in a dishwasher. The burner can be dismantled and cleaned when cool. ^ Remove the burner parts and wash them in a solution of warm water and liquid dish soap. Dry them thoroughly. -
Page 18: Frequently Asked Questions
Frequently asked questions Repairs should only be carries out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. The manufacturer cannot be held responsible for unauthorized work. The burner does not ignite after several attempts. Possible fault The burner is not assembled correctly. -
Page 19: Technical Service
Technical Service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting Technical Service please quote the serial number and model of the appliance. - Page 20 Miele Service department, Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele. Our goal is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further damage to them, you and/or your home.
-
Page 21: Installation Instructions
Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE To prevent accidents and appliance damage read these instructions before installation or use. -
Page 22: Important Safety Instructions
However, under certain conditions it may be possible for installation in these applications. Please contact the Miele Technical Service Department with specific requirements. The combiset must not be installed over a dishwasher, washer, dryer, refrigerator or freezer. -
Page 23: Safety Distances Above The Appliance
Safety distances above the appliance The minimum safety distance given by the hood manufacturer must be maintained between the combiset and the hood above it. See the installation instructions of the hood for these safety measurements. If the hood manufacturers instructions are not available or if flammable objects are installed over the combiset (e.g. - Page 24 IMPORTANT SAFETY INSTRUCTIONS Safety distances to the sides of the appliance The appliance should only be installed as shown in the illustrations, while maintaining the required safety distances shown. Do not install the appliance between two tall cabinets, this is a fire hazard. A distance of at least 2"...
-
Page 25: Installation
Safety distance from the wall covering If a wall covering is installed, a minimum safety distance must be maintained between the countertop cut-out and the covering, since high temperatures can damage these materials. If the covering is made of a combustible material (such as wood), the distance between the countertop cut-out and the wall covering must be a minimum of 2"... -
Page 26: Installation Dimensions
Installation Installation dimensions Spring clips Appliance front Installation height Power supply box with connection cable, L = 78 3/4" (2000 mm) Gas fitting Rating label... -
Page 27: Cut Out
Cut out ^ Make the countertop cut-out for one or more appliances as applicable. Remember to maintain a minimum safety distance from the back wall, as well as from any tall unit or side wall to the right or left of the hob. See "IMPORTANT SAFETY INSTRUCTIONS". -
Page 28: Installation Of Multiple Appliances
Installation Installation of multiple appliances When installing more than one combiset appliance, a support bar installed between the appliances. Countertop cut-out two appliances For the installation of two appliances the width of the countertop cut-out D is the sum of A and C. A, B and C = appliance width 11 5/16", 15"... - Page 29 Sample calculations for a countertop cut-out for three appliances appliance width appliance width minus 5/16" (8 mm) 11" (280 mm) 11 5/16" (288 mm) 11" (280 mm) 15" (380 mm) 11" (280 mm) 22 11/16" (576 mm) 14 5/8" (372 mm) 11 5/16" (288 mm) 14 5/8"...
- Page 30 Installation Spring clips Support bars Space between support bar and countertop Sealing strip The illustration represents the attachment of spring clips for 3 appliances. An additional support bar is required for each additional appliance. The position for attachment of an additional support bar depends on the width of appliance B. and support bars...
-
Page 31: Attach The Spring Clips And Support Bars
Attach the spring clips and support bars Wood or solid surface countertops ^ Place the supplied spring clips and the support bars marked positions as shown above, by laying them on the upper edge of the cut-out and then securing them with the "... - Page 32 Installation Granite countertop The screws are not needed for granite countertops. 3 / 1 6 " 1 " - 1 m m ) ( 2 5 - 3 0 ^ Position and attach the spring clips and support bars double-sided tape ^ Coat the edges of the spring clips ^ and the space support bars...
-
Page 33: Installing The Appliance / Appliances
Installing the appliance / appliances ^ Feed the power cord down through the cut-out. ^ Place the front edge of the appliance into the cut-out. ^ With a hand on each side of the appliance press down evenly on the edges until it clicks into position. -
Page 34: Sealing
Installation Sealing The appliance must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the appliance provides a sufficient seal for the countertop. If the appliance is sealed into position, the countertop or appliance could be damaged if it needs to be removed for maintenance or service. -
Page 35: Electrical Connection
This appliance must be grounded according to local or national codes. All electrical work should be performed by a qualified electrician in accordance with local codes and with the: National Electrical Code ANSI / NFPA No. 70 for the USA Canadian Electrical Code Part I for Canada (CSA Standard C 22.1). - Page 36 Electrical connection Wiring Diagram...
-
Page 37: Gas Connection
Installation and service must be performed by a qualified installer, service agency or the gas supplier. In Massachusetts a licensed plumber/gas fitter is required. This appliance must be installed with its own shut off valve and the included gas pressure regulator. Both the valve and the regulator must be easily accessible to the consumer to turn on or shut off the... -
Page 38: Gas Pressure Regulator
½" NPT Regulator As shown in the above diagram, the included regulator must be used when connecting the Miele combiset to your gas supply. This item has been customized by Miele to meet all applicable safety requirements. Make sure the regulator is easily accessible for adjustment after the appliance has been installed. -
Page 39: Nominal Ratings
Nominal ratings Maximum output Gas type BTU/hr Natural Gas (NG) 27,600 Liquid Gas 22,200 (Propane) (LP) Minimum output Gas type BTU/hr Natural Gas (NG) Liquid Gas (Propane) (LP) 5,700 1.67 5,700 1.67 Gas connection... -
Page 40: Converting To Another Type Of Gas
Converting to another type of gas The combiset should have been ordered for connection to either natural gas or LP gas (propane). If the combiset is not configured for the proper type of gas connection please contact your Miele Dealer. -
Page 41: Help Protect Our Environment
Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Help protect our environment Disposal of an old appliance Old appliances contain materials that can be recycled. - Page 44 Alteration rights reserved / 2409 M.-Nr. 07 369 720 / 02 For the most updated manual see the Miele web site.