Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NEC NEC MultiSync V721 60000531 60000531
Summary of Contents for NEC NEC MultiSync V721 60000531 60000531
- Page 1 MultiSync V521 MultiSync V721 MultiSync V921 User’s Manual...
-
Page 2: Declaration Of The Manufacturer
MultiSync V721(N0701) MultiSync V921(N9902) are in compliance with Council Directive 73/23/EEC: Council Directive 89/336/EEC: and marked with NEC-Mitsubishi Electric Visual Systems Corporation KANAGAWA 258-8533, JAPAN - EN 60950 - EN 55022 - EN 61000-3-2 - EN 61000-3-3 - EN 50082-1... -
Page 3: Safety Instruction
Microsoft and Windows are registered trademarks of the Microsoft Corporation. is a U.S. registered mark. NERGY NEC is a registered trademark of NEC Corporation. All other trademarks or registered trademarks are property of their respective owners. emblem does not NERGY... - Page 4 Contents V Series monitor box* should contain the following: • MultiSync V Series Monitor with tilt / swivel base MultiSync V521, MultiSync V721 or MultiSync V921 • Power cord • Captive Signal Cable • User‘s manual • CD-ROM includes complete User‘s Manual in PDF format and Windows related files (Inf file and color profile).
- Page 5 Tilt / swivel base fixing, removing Fixing This product consists of the MultiSync monitor and the tilt / swivel base. When fixing the tilt / swivel base to the MultiSync monitor, please follow the steps below. • Push the six hooks of the tilt / swivel base into the six holes at the bottom of the MultiSync monitor.
-
Page 6: Quick Start
Quick Start To attach the MultiSync V Series monitor to your system, follow these instruction: 1. Turn off the power to your computer and MultiSync monitor. 2. If necessary, install the display card. For more information, refer to the display card manual. 3. - Page 7 Computer Power Outlet Power cord Captive Signal Cable Mac Adapter 15-pin mini D-SUB (not included) Figure B.1 Figure C.1 Figure D.1 English-6...
-
Page 8: Select Control
Controls OSM (On-screen Manager) control buttons on the front of the monitor function as follows: SELECT Enters and exits the OSM menu. CONTROL-/+ Selects one of the controls and decreases or increases the adjustment. RESET Resets the highlighted control to the factory setting. Press -/+ button at the same time for approximately 1 sec. - Page 9 Parallelogram: Decreases or increases the tilt of the sides either to the left or right. Bow (Pincushion Balance): Decreases or increases the curvature of the sides either to the left or right. Rotates: Rotates the image. Degauss: Select the degauss icon on “Icon select window” and push “SELECT”...
-
Page 10: Recommended Use
Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC V SERIES • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. - Page 11 • In UK, use a BS-approved power cord with molded plug having a black (5A) fuse installed for use with this monitor. If a power cord is not supplied with this monitor, please contact you supplier. Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions: •...
- Page 12 • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 30 cm and no further away than 70 cm from your eyes.
-
Page 13: Specifications
Invar Shadow Mask. Depends on display card used. Automatically Automatically Some systems may not support all modes listed. NEC-Mitsubishi Electronics Display cites recommended resolution at 85 Hz for optimal display performance. Dependent upon signal timing used, and does not include border area. - Page 14 Invar Shadow Mask. Depends on display card used. Automatically Automatically Some systems may not support all modes listed. NEC-Mitsubishi Electronics Display cites recommended resolution at 85 Hz for optimal display performance. Dependent upon signal timing used, and does not include border area.
- Page 15 OptiClear creen surface Depends on display card used. Automatically Automatically Some systems may not support all modes listed. NEC-Mitsubishi Electronics Display cites recommended resolution at 85 Hz for optimal display performance. Dependent upon signal timing used, and does not include border area.
- Page 16 Features OptiClear Screen Surface (MultiSync V921 Monitor only): Reduces reflection and glare and increases contrast without sacrificing focus level, clarity or brightness. Along with the flat square technology CRT, a high contrast screen with 0.26 mm trio dot pitch delivers crisp, clean text and graphics.
- Page 17 Mode (IPM Mode (Power Switch, Off) Reduced Magnetic Field Technology: Reduces magnetic and alternating electric field emissions and static electricity, addressing ergonomic concerns regarding potential risks from extended computer monitor use and is compliant with MPRII and TCO‘99. Multiple Frequency Technology: Automatically adjusts monitor to the display card‘s scanning frequency, thus displaying the resolution required.
-
Page 18: Troubleshooting
Troubleshooting No Picture • The display card should be completely seated in its slot. • Power Switch and computer power switch should be in the ON position. • The signal cable should be completely connected to the display card/ computer. •... - Page 19 TCO‘99 Congratulation! You have just purchased a TCO‘99 approved and labeled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
-
Page 20: Environmental Requirements
The environmental demands concern restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must be prepared for recycling and the manufacturer is obliged to have an environmental plan which must be adhered to in each country where the company impl ements i ts operational policy. -
Page 21: Cfcs (Freons)
Cadmium** Cadmium is present in rechargeable batteries and in the colour- generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. TCO‘99 requirement states that batteries, the colourgenerating layers of display screens and the electrical or electronics components must not contain any cadmium.