hit counter script
Bosch C60 Manual
  1. Manuals
  2. Brands
  3. Bosch Manuals
  4. Data Loggers
  5. C 60
  6. Manual

Bosch C60 Manual

Hide thumbs Also See for C60:
Table of Contents

Advertisement

Quick Links

Download this manual
Data Logger C60
Manual
Version 1.1 24/06/2020

Advertisement

Table of Contents
loading

Related Manuals for Bosch C60

Summary of Contents for Bosch C60

  • Page 1 Data Logger C60 Manual Version 1.1 24/06/2020...

  • Page 2: Table Of Contents

    11.3 Configuration of Online Telemetry................................11.4 Configuration of Burst Telemetry................................... 11.5 Recording on USB Memory....................................12 Lap Trigger ..................................12.1 Lap trigger (timing beacon)....................................12.2 Counting outing/laps/fragments ................................... 12.3 Lap timing..........................................12.4 Segment timing........................................12.5 Countdown timer ......................................... ii / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 3 14.5 GPS troubleshooting......................................15 Fuel Consumption Calculation ............................15.1 Setting up fuel consumption calculation and tank management ..................... 15.2 Fuel consumption diagnosis/counter reset..............................15.3 Example ............................................ 16 Clone the Unit ................................. 17 RaceCon Shortcuts................................18 Disposal.................................... Bosch Motorsport Data_Logger_C_60_Manual iii / 100...

  • Page 4: Preparation

    The use of variant combinations, accessories, and other devices out- side the scope of this manual are only permitted when they have been determined to be compliant from a performance and safety standpoint by a representative from Bosch Motorsport.

  • Page 5: Warnings And Safety Instructions

    Warning of death or serious injury, which can occur if this is not observed. Caution CAUTION Nature and source of danger Consequences Warning of slight bodily injury in case of Disregard. Notice NOTICE Nature and source of danger Consequences Warning of damage to equipment in case of ignoring. Bosch Motorsport Data_Logger_C_60_Manual 5 / 100...

  • Page 6: Onboard Network Concept

    Be careful to observe current limits of wires and connector pins! IGN- Switch UBAT Star connection switched pos. terminal (term30) positive terminal Electric Loads Main KL15 Switch KL30 Bosch Motorsport Device diagnosis connector µC LS_SWITCH1…4 KL31 UBATT_FUSE GND_Starpoint SENSPWR10 Star connection Chassis dig. sensors (e.g. wheelspeed)

  • Page 7: Error Memory

    DDU 8. Please consider this and replace the product name ‘DDU 8’ in this case with the name of your product. 4.1 Error memory representation in RaceCon Bosch Motorsport devices feature an error memory. Information on errors can be visual- ized via RaceCon (online measurement) or can be transmitted via telemetry. 4.1.1 Accessing the memory...
  • Page 8 The error memory is not cleared by a configuration download and is not cleared by a power cycle. 4.1.2 Clearing the error memory There are two ways of clearing the error memory, both are shown in the following illustra- tion: 8 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 9: Information On Errors Available From The Error Memory

    1: at least one inactive error present in memory, no active errors 2: at least one active error present in memory If displayed in a measurement sheet, this property’s value (0, 1 or 2) is translated into a verbal description: Bosch Motorsport Data_Logger_C_60_Manual 9 / 100...
  • Page 10 0 (no error present in memory): No orange border MIL off (black) No entries 1 (at least one inactive error present in memory, no active errors): Constantly orange border MIL constantly orange Info cycling through errors, present in error memory 10 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 11 All failure modes are continuously diagnosed; any error detected will be written to the error memory. Once an error is detected, it is qualified as “active”. – 1 (TRUE) Error was detected in most recent diagnose run (active) Bosch Motorsport Data_Logger_C_60_Manual 11 / 100...
  • Page 12 (while more than one error is active) and watch the values change periodically: The verbal representation of the numerical codes of these labels can be visualized in the properties window of the measurement page: 12 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 13: Analog Input Diagnosis

    The pin diagnosis functionality (check whether measurement is within the desired range) can be activated in the ANA pin setup wizard; to allow for a diagnosis regarding shortcut to ground, shortcut to battery voltage and cable breakage, a minimum / maximum has to be defined. Bosch Motorsport Data_Logger_C_60_Manual 13 / 100...
  • Page 14 Open the Error Memory of the Device. Click "start detection of cable". Check the Error Memory for new fault entries, regarding "Open line errors". 14 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 15: Technical Data

    Mechanical Data Size 105 x 34.5 x 137.5 mm Weight 495 g Protection Classification IP67 to DIN 40050, Section 9, Issue 2008 Operating temperature (internal) -20 to 65°C Max. vibration Vibration profile 1 (see Appendix or www.bosch-motorsport.com) Bosch Motorsport Data_Logger_C_60_Manual 15 / 100...
  • Page 16 PWM outputs (low side switch 2 A each) Sensor supply 5 V ± 1 % (250 mA) Environment USB Kit for C 60 Rugged USB flash drive Bosch File System (BFS) format included, works with BFS pre- formatted USB flash drive only Adapter cable to USB-Port...
  • Page 17 Low-Side Ground2 ANAIN_M1_1 0 to 5V Analog ANAIN_M1_2 0 to 5V Analog ANAIN_M1_3 0 to 5V Analog ANAIN_M1_4 0 to 5V Analog ANAIN_M1_5 0 to 5V Analog ANAIN_M1_6 0 to 5V Analog ASDD212-41PA Name Description UBATT_FUSE1 SENSPWR10_1 Bosch Motorsport Data_Logger_C_60_Manual 17 / 100...
  • Page 18 0 to 5V Analog ANAIN_M2_7 0 to 5V Analog ANAIN_M2_8 0 to 5V Analog ANAIN_M2_9 0 to 5V Analog ANAIN_M2_10 0 to 5V Analog LAPTRIGGER Installation Notes Inspection services recommended after 110 h or 12 months. 18 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 19 Technical Data | 5 Depending on your experience calibrating Bosch ECUs, we recommend calibration sup- port from Bosch Motorsport. Please remember that the mating connectors and the programming interface MSA Box II are not included and must be ordered separately.

  • Page 20: Mechanical Drawing

    6 | Mechanical Drawing 6 Mechanical Drawing 20 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 21: Starting Up The C 60

    Click ‘OK’ Click when done ‘Properties’ 7.1.2 Power up the C60 – The C 60.LEDs will illuminate – The ‘Link LED’ at the PC’s network adapter will illuminate – If the LED is off, check the wiring harness Bosch Motorsport Data_Logger_C_60_Manual 21 / 100...
  • Page 22 7 | Starting up the C 60 7.1.3 Connecting the Unit to RaceCon The following screenshot shows an overview of the RaceCon Main Screen with its areas. All (sub-) windows are resizable and dockable. Start the RaceCon software. 22 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 23: Feature Activation

    – As the activation key is device specific, a key delivered with one C 60 does not work on any other C 60 . – If you have not purchased an option package, the next steps can be skipped. Bosch Motorsport Data_Logger_C_60_Manual 23 / 100...

  • Page 24: First Recording

    Start the WinDarab software. Disconnect the C 60 network cable. 10. Click on the ‘Import/Export’ icon. 11. Select ‘Data logger C50/C55/C60/DDU7/DDU8’ and click ‘OK’ when done. The ‘Read measurement Data’ dialog opens. 12. Click on ‘Modify’ button and select the base folder.

  • Page 25: Status Leds

    Once this accumulator is charged correctly by 12 V supply of the C 60, ‘Date & Time’ can be programmed by RaceCon. We recommend min. 5 hours charge time. Please connect the C 60 to the PC and click on ‘Set Date & Time’ in the Context menu of the C 60. Bosch Motorsport Data_Logger_C_60_Manual 25 / 100...
  • Page 26 7 | Starting up the C 60 26 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 27: Can Configuration

    CAN bus items of the project tree Row Counter Concept – Re-use (multiplex) of message identifiers – One byte of message contains row counter – 7 bytes payload remaining – Position of row counter is configurable Bosch Motorsport Data_Logger_C_60_Manual 27 / 100...

  • Page 28: Can Input

    8.2.2 Create new CAN Input channel Double-click on any CAN bus item, to open the "CAN messages overview". Select ‘Add CAN-IN’ and choose the desired CAN bus for the new input channel. A CAN channel configuration window opens. 28 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 29 CAN Configuration | 8 Insert the name and description of the channel. Click ‘OK’ when done. The channel is listed in the Data window. Bosch Motorsport Data_Logger_C_60_Manual 29 / 100...
  • Page 30 Enter CAN message ID. If extended IDs (29 bit) are used, check the box. b) If replacement values are used, specify time-out period and raw value. c) If a multiplexer (row counter) is used, check the box. 30 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 31 Enter offset for conversion to physical value. c) Select type of physical value. d) Select unit of physical value. e) Enter minimum physical limit of the channel. (for manual setup) f) Enter maximum physical limit of the channel. (for manual setup) Bosch Motorsport Data_Logger_C_60_Manual 31 / 100...
  • Page 32 Double-click on ‘Sheet 1’ in Project Tree. Measurement Sheet 1 is displayed in Main Area. Click on ‘Measurement elements’ in the Toolbox. Drag the desired Measurement element (e.g. Numeric Indicator) and drop it on the Measurement Sheet. 32 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 33 8.2.5 Import a CAN database (DBC) file Right-click on CAN Input of desired bus (CAN1 or CAN2). Select ‘Import DBC file’ from menu. A file browser opens. Select DBC file to import and click ‘OK’ when done. A channel import window opens. Bosch Motorsport Data_Logger_C_60_Manual 33 / 100...

  • Page 34: Can Output

    8.3.2 Create a new CAN output message channel – Double-click on any CAN bus item, to open the "CAN messages overview". – Select ‘Add CAN-OUT’ and choose the desired CAN bus for the new output channel. 34 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 35 Definition of CAN message Content of message – Click on ‘Add channel’ or ‘Add constant’, this opens the ‘Add new CAN out channel’ window. – Select the desired measurement channel and specify the message settings. Bosch Motorsport Data_Logger_C_60_Manual 35 / 100...

  • Page 36: Multiplexer

    – Re-use (multiplex) of message identifiers by splitting it into several rows. – Every row is assigned to a unique value of the multiplexer. – One byte of message contains row counter. 36 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 37 Select a channel and configure it. To assign it to the row selected before, check the box ‘Multiplexed’. To move the channel message, change the “Start” value or click and hold the green field in the “Add new CAN out message” window. Click ‘OK’ when done. Bosch Motorsport Data_Logger_C_60_Manual 37 / 100...
  • Page 38 8 | CAN Configuration 10. The channel message is assigned to the selected fields. 11. Click ‘OK’ when done. 38 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 39: Analog And Frequency Inputs

    – C 60 uses A/D converter oversampling and digital filtering to recording rate – Digital filters eliminate ‘out-of-band’ noise – Cut-off frequency automatically adjusted to recording rate – Linear phase - no signal distortion – Latency compensation - no filter delay in recorded data Bosch Motorsport Data_Logger_C_60_Manual 39 / 100...

  • Page 40: Configuring Inputs

    Expand the list of ‘I/O Channels’ by clicking on ‘+’ in the C 60 Project Tree. Drag the ‘Bosch Sensor Wizard’ from the Toolbox and drop it on the desired analog input channel in the C 60 Project Tree. The ‘Bosch Sensor Wizard’ opens.
  • Page 41 Example: Acceleration sensor 5 g From sensor data sheet – operating characteristics: Sensitivity 400 mV/g, Offset 2500 mV The sensor has a linear output signal with sensitivity and offset Click on ‘Measurement Sources’ in the Toolbox. Bosch Motorsport Data_Logger_C_60_Manual 41 / 100...
  • Page 42 Click ‘Next’ when done. The second part of the ‘Sensitivity/Offset Wizard’ opens. Choose unit group and unit of physical value Enter values Physical from sensor (channel) datasheet value Electrical (pin) value Click ‘Next’ when done. The third part of the ‘Sensitivity/Offset Wizard’ opens. 42 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 43 9.3.3 Configuring a generic non-linear sensor Example: Thermistor 5 kOhm – From sensor data sheet: resistance values over temperature Bosch Motorsport Data_Logger_C_60_Manual 43 / 100...
  • Page 44 5V signal at the analogue channel of the C 60. It allows you to use a push-button. The fixed value of the internal pull up-resistor is 3010 Ohm. If using an additional external pull up-resistor, set up the overall resistance. 44 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 45 The channel is inserted into the C 60 Project Tree. Channel is linked to ANA05 Input pin Characteristic Adjustment Pull-up curve for is disabled resistor is sensor activated Available measurements for channel: Measurement label Function raw_name mV value of sensor Bosch Motorsport Data_Logger_C_60_Manual 45 / 100...
  • Page 46 Expand the list of ‘I/O Channels’ by clicking on ‘+’ in the C 60 Project Tree. Drag the ‘Multipoint Adjustment’ analog signal source from the Toolbox and drop it on the desired analog input channel in the C 60 Project Tree. A ‘Multipoint Adjust- ment Wizard’ opens. 46 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 47 Click ‘Next’ when done. The third part of the ‘Multipoint Adjustment Wizard’ opens. Enter physical limits of the sensor Choose data type of Physical the measurement limits of variable channel Enable additonal online calibration Enter name to automatically create a new measurement sheet Bosch Motorsport Data_Logger_C_60_Manual 47 / 100...
  • Page 48 Online definition of the curve is covered in the chapter ‘Online calibration of measurement channels’ of this manual. 9.3.5 Digital filter details C 60 uses A/D converter oversampling and digital filtering to recording rate. Digital filters eliminate ‘out-of-band’ noise 48 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 49 This function requires the installation of Software Upgrade 1. Example: measurement of wheel speed – Pulse wheel attached to wheel – Each passing tooth of pulse wheel triggers hall sensor – Calculation of wheel speed with wheel circumference Bosch Motorsport Data_Logger_C_60_Manual 49 / 100...
  • Page 50 Input pin Number of Wheel has hall teeth circumference interface Available measurements for channel: Measurement label Function raw_name mV value of sensor raw_name_fi filtered mV value of sensor name physical value of sensor name_fi filtered physical value 50 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 51: Computed Sources

    Channels’ in the C 60 Project Tree. A ‘Computed Sensitivity/Offset Wizard’ opens. Choose input channel Choose unit group and unit of output Enter sensitivity and offset of conversion formula Click ‘Next’ when done. The second part of the ‘Computed Sensitivity/Offset Wizard’ opens. Bosch Motorsport Data_Logger_C_60_Manual 51 / 100...

  • Page 52: Hysteresis

    The hysteresis function avoids the high-frequent switchover of the measurement channel value. The hysteresis can be adjusted for each input measurement channel individually and can be used for further processing. Click ‘Measurement Sources’ in the Toolbox. 52 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 53 Enter time when the hysteresis function is activated after vehicle’s startup. j) Enter the channel’s state (A or B) at startup. Click ‘Next’ when done. The second part of the ‘Hysteresis Wizard’ opens. Click ‘Finish’ when done. Enter channel name and description. Bosch Motorsport Data_Logger_C_60_Manual 53 / 100...
  • Page 54 – Calculating vehicle speed of 4 wheel drive: (Wheel speeds of all wheels as input) Calculated speed is speed of 2nd fastest wheel. 9.5.2 Setting up calculated speed Click on tab ‘System Overview’. Click on ‘Measurement Sources’ in the Toolbox. 54 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 55: Configuring Pwm Outputs

    DDU 8 Project Tree Measurement channels Configu- calculated ration speed and window calculated distance 9.6 Configuring PWM outputs – Pulse Width Modulation – Output frequency is constant – ‘On time’ (duty cycle) controlled by input channel Bosch Motorsport Data_Logger_C_60_Manual 55 / 100...
  • Page 56 Drag the ‘PWM Out’ computed source from the Toolbox and drop it on the desired ‘PWM_OUT’ channel in the C 60 Project Tree. A ‘PWM Out Wizard’ opens. Choose input channel Choose output frequency Define characteristic curve Enter name to automatically create a new measurement sheet 56 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 57 PWM output 1 error over temperature pwm_err_ls_out_01_SCB PWM output 1 error short circuit to battery pwm_err_ls_out_01_SCG PWM output 1 error short circuit to GND Table 1: Diagnostic channels NOTICE The diagnosis of PWM output 2-4 is similar. Bosch Motorsport Data_Logger_C_60_Manual 57 / 100...

  • Page 58: Online Measurement And Calibration

    ‘Sheet 1’ opens in a new ‘Calibration/Measuring’ window. RaceCon changes automatically to "Calibration/ Measuring" Click on the ‘Folder/Sheets’ tab, which appears when you are in the ‘Calibration/ Measurement’ window, to create a new measurement folder. 58 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 59 Drag a measurement element from the Toolbox and drop it on the measurement sheet. Drag + Drop Select the desired measurement channel from the ‘Data’ area and drop it on the measurement element. If the C 60 shows the green status, the value is displayed. Bosch Motorsport Data_Logger_C_60_Manual 59 / 100...
  • Page 60 Numeric indicator Oscilloscope (Chart) 10.1.1 Automatic creation of measurement sheets RaceCon can create measurement sheets automatically. You can create and use measurement sheets with the C 60 as well as with all other devices connected to RaceCon. 60 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 61 Drag + Drop During the configuration of a measurement channel, select a measurement sheet from the list box or enter a name for a new measurement sheet. Select existing sheet from list or enter name of new sheet Bosch Motorsport Data_Logger_C_60_Manual 61 / 100...
  • Page 62 Mode’. The measurement sheet is extended to full screen. The button for offset calib- ration is active. Switch between different sheets using the tabs at the bottom of the window. Press the ‘Esc’ key to return to ‘Design Mode’. 62 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 63: Online Calibration Of Measurement Channels

    – Analog sensors drift with age, temperature, etc. – Manual calibration is necessary – Solution: online offset calibration – Example: acceleration sensor 10.2.1 Enable online offset calibration for measurement channel During creation of the measurement channel Bosch Motorsport Data_Logger_C_60_Manual 63 / 100...
  • Page 64 Open the measurement channel’s online page by double-clicking on the measure- ment channel name in the Data Area. Enter the physical target value (e.g. 1 G) and press the ‘Calibrate’ button. Calibration target value Initiate calibration The sensor’s offset is now calibrated. 64 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 65: Online Calibration Of Multipoint Adjustment Channels

    Click on ‘Calibrate adjustment points’ to open calibration window. Apply the desired physical condition to the sensor (e.g. by applying a force on the wheel). Enter the physical value in the value column of the desired calibration point (e.g. 745 N). Bosch Motorsport Data_Logger_C_60_Manual 65 / 100...
  • Page 66 10 | Online Measurement and Calibration Press the ‘Calibrate’ button of the desired calibration point. Repeat for all curve points. 10. Click ‘Close’ when done. The calibration curve is displayed in the online view. Adjustment points vs. offset adjustment 66 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 67: Recording And Telemetry

    If no condition is defined or condition is ‘false’, measurement chan- nels are recorded at the value chosen in ‘Rate’. If the condition is ‘true’, measurement channels are recorded at the value chosen in ‘True rate’. Click ‘OK’ when done. Bosch Motorsport Data_Logger_C_60_Manual 67 / 100...
  • Page 68 ‘Gearbox’, ‘Aero’, ‘Engine’, etc. 11.2.3 Logger settings To display the global C 60 settings, open the ‘Logger’ window and click on the ‘Settings’ tab at the bottom. a) Choose setting for outing counter mode: 68 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 69 Choose wether the logging partition shall be named Engine recording or Chassis re- cording. c) Advanced setting: Select your logging configuration file, if provided by your Bosch Sup- port Engineer. d) Choose or create the condition to start recording e) Enter a password hint and a password (optional).

  • Page 70: Configuration Of Online Telemetry

    Expand the list of ‘Loggers’ by clicking on ‘+’ in the C 60 Project Tree. Double-click on ‘Recording’ in C 60 Project Tree. The recording configuration is dis- played in the Main Area. Click ‘Edit channel(s)’. The ‘Edit Recording Channels’ window appears. 70 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 71 Click on the ‘Settings’ tab at the bottom, to edit the channels. Assign the desired channels to the channel types. The table below shows the function of the available channel types. Click ‘Ok’ when done. Bosch Motorsport Data_Logger_C_60_Manual 71 / 100...

  • Page 72: Configuration Of Burst Telemetry

    USB_DATA, enter the license key as described in the chapter ‘Feature activation [} 23]’. For USB recording, Software Upgrade FULL_LOG_1 should also be enabled. Wiring harness Value USB_Device_Power Power (red) USB_Device_DP D+ (green) USB_Device_DN D- (white) USB_Device_Gnd GND (black) For further information, see the pinlayout of the device. 72 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 73 Storage device The recording function can be used with a dedicated Bosch Motorsport USB device. The USB device has to be preformatted with the Bosch File System (BFS) in RaceCon before first use. To format the USB device with the Bosch File System (BFS), do the following steps: In RaceCon, select ‘Tools’...
  • Page 74 19. Drag the desired measurement channel from the Channel list and drop it into the measurement data window. The measurement channel‘s graph is displayed. NOTICE For more detailed descriptions and instructions refer to the Win- Darab V7 manual. 74 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 75: Lap Trigger

    – Analog input – Digital input – CAN input Signal (measurement channel) properties Low active signal (Bosch triggers): Trigger releases if signal is below the threshold. High active signal (other manufacturer’s triggers): Trigger releases if signal is above the threshold. Bosch Motorsport Data_Logger_C_60_Manual 75 / 100...
  • Page 76 – Main trigger (end‐of‐lap at start/finish line) – Sub‐trigger (segment time, optional, not applicable with GPS lap trigger) Bosch standard: – Main trigger 20 ms, low active (Recommendation for RaceCon “Detecion Time” set- ting: 15 ms, Setting must be a slightly shorter period than the signal length of the trigger to avoid a missed trigger due to the update rate) –...
  • Page 77 Under race conditions, trigger signals are sometimes missed. Software functionality intro- duces ‘forced trigger’. 12.1.5 Setting up a lap trigger Click ‘Measurement Sources’ in Toolbox. Drag ‘Laptrigger’ into ‘System Overview’. Do not drop it on ‘C 60’! Bosch Motorsport Data_Logger_C_60_Manual 77 / 100...
  • Page 78 Change signal channel, if desired. c) Choose signal threshold. See chapter 'Electrical trigger signal' for details. d) Define threshold of input channel signal when trigger is released. Only possible, if no digital source is selected as signal source. 78 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 79 Enter minimum speed for trigger release. Define settings for distance based retrigger protection. Define settings for distance based forced trigger. Define settings for lap timing (main trigger). Define settings for sub trigger. Not applicable with a GPS lap trigger. Bosch Motorsport Data_Logger_C_60_Manual 79 / 100...
  • Page 80 To display a quick lap trigger channel diagnosis and to reset counters use the diagnosis page in RaceCon. Any ‘Laptrigger_xxx’ channel can be displayed. Double-click on any ‘Laptrigger_xxx’ channel in the Data Area. Example: ‘laptrigger_lap- dist_dls’ A diagnosis window opens in Main Area. 80 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 81: Counting Outing/Laps/Fragments

    Preset values for lap counter and outing counter Minimum laptime that a new 'best laptime' is accepted Preset value for 'best laptime' 12.2 Counting outing/laps/fragments Functionality – Power ON: system + measurement is initialized but not yet started Bosch Motorsport Data_Logger_C_60_Manual 81 / 100...

  • Page 82: Lap Timing

    The detection time defines the minimum time the input signal changes its state. E.g. a low active signal needs to be below the threshold for min. 15 ms to release the trigger. Channels for display To display lap times use the following channels: Channel Function Laptrigger_lapctr_dls Number of completed laps 82 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 83 4000 m) has been covered. To deactivate distance based retrigger protection, set min dis- tance to 0 %. Change signal for vehicle speed, if desired. Enter minimum speed for trigger release. Define settings for distance based retrigger protection. Define settings for distance based forced trigger. Bosch Motorsport Data_Logger_C_60_Manual 83 / 100...

  • Page 84: Segment Timing

    Segment timing is the calculation of elapsed time for parts of laps (segments). Segments are defined: – based on sub-trigger signals (additional transmitters) – based on distance travelled Times for segments are compared to: – Last lap completed – Fastest lap 84 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 85 Set ‘Mode’ to ‘Distance’ and enter desired segment distances. Segment time is automatically calculated at each segment. Time difference to last lap and fastest lap is automatically calculated at each segment. To deactivate distance mode set ‘Mode’ to ‘None’. Bosch Motorsport Data_Logger_C_60_Manual 85 / 100...

  • Page 86: Countdown Timer

    The trigger signal starts a timer countdown. The current value of the timer is stored in the variable Laptrigger_cntdown_dls which can be displayed. Define settings for countdown timer. 86 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 87: Automatic Gps Track Detection

    GPS tab with the button “Set values …”. This allows an easy interaction with the manual GPS lap trigger mode. The user-defined tracks will be part of the project. If the tracks are required in another project, the lap trigger module can be ex-/imported into another project. Bosch Motorsport Data_Logger_C_60_Manual 87 / 100...
  • Page 88 Laptrigger_trackdet_laplen Track length of the used track variant Laptrigger_trackdet_lat Latitude GPS coordinate of the used GPS trigger point Laptrigger_trackdet_long Longitude GPS coordinate of the used GPS trigger point 88 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 89: Firmware

    60! When the firmware update is complete, the C 60 displays the message ‘Up- dating firmware finished. Do a powercycle.’ Switch the car’s ignition off and on again to cycle the power of theC 60. Bosch Motorsport Data_Logger_C_60_Manual 89 / 100...

  • Page 90: Gps Sensor

    This sensor is based on a U-Blox 8 chipset and is fully configurable with the Navilock “U-Center” software. To use this sensor with Bosch Motorsport components the transfer rate, the satellite system and the update rate needs be reconfigured. More in- formation about the configuration can be found in the Appendix.

  • Page 91: Gps Troubleshooting

    – Is the transmitter signal of the GPS sensor connected to the receiver pin of serial in- terface 2 of the C 60? – Is the GPS sensor powered up? – Does the GPS sensor deliver RS232 signal levels? Bosch Motorsport Data_Logger_C_60_Manual 91 / 100...
  • Page 92 – Does the GPS sensor ‘view’ the sky? – Did the GPS sensor complete its initial start-up procedure? This may take up to 20 min. – A correct reception is indicated when ‘gps_fix’ is showing ‘3D Fix’. 92 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 93: Fuel Consumption Calculation

    Double-click on any ‘fuel_xxx’ channel in channel list. A diagnosis window opens in Main Area. Button to reset total fuel consumption (Reset with RaceCon only) Button to reset fuel consumption manually (Can also be Settings triggered ‘by signal overview source’ or ‘on power down’) Bosch Motorsport Data_Logger_C_60_Manual 93 / 100...

  • Page 94: Example

    Running fuel consumption, starting at ‘0’ Fuel_fuelrem_dls Remaining fuel in tank, starting at tank capacity Fuel_fuellap_dls Fuel consumption for current lap, starting at ‘0’ Fuel_fuellapold_dls Fuel consumption of last lap completed Fuel_laprem_dls Remaining laps with fuel in tank 94 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 95: Clone The Unit

    Click ‘OK’ to start procedure. Change the device. Click ‘Clone apply’ in Extras menu. Choose clone file. Click ‘Ok’. Please remember that following properties are not stored into the clone: – Lifetime of device – Serial number – Upgrade features Bosch Motorsport Data_Logger_C_60_Manual 95 / 100...

  • Page 96: Racecon Shortcuts

    Open all nodes Delete seleted object Display page, measurement page Cursor Move selected display element one grid unit in chosen dir- ection SHIFT + cursor Enlarge/reduce selected display element one grid unit Switch between display elements 96 / 100 Data_Logger_C_60_Manual Bosch Motorsport...

  • Page 97: Disposal

    Disposal | 18 18 Disposal Hardware, accessories and packaging should be sorted for recycling in an environment- friendly manner. Do not dispose of this electronic device in your household waste. Bosch Motorsport Data_Logger_C_60_Manual 97 / 100...
  • Page 98 98 / 100 Data_Logger_C_60_Manual Bosch Motorsport...
  • Page 99 Bosch Motorsport Data_Logger_C_60_Manual 99 / 100...
  • Page 100 Bosch Engineering GmbH Motorsport Robert-Bosch-Allee 1 74232 Abstatt Germany www.bosch-motorsport.com...

Table of Contents