Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also
recommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are
plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual
Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.
and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that none is loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When an ASTA/BS approved UK
3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol
To rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket
with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
1.2.
GENERAL SAFETY
WARNING! Disconnect the heater from the mains power, before servicing or performing any maintenance, which must only be carried
out by an authorised service agent. Report any oil leakage immediately to an authorised service agent.
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Ensure that the heater is used in an area larger than 4m³. Allow a few centimetres of clearance from any surface, and ensure there is
good overhead clearance for heat circulation.
Only use the heater in an upright position.
WARNING! do not tamper with the wiring, heating element or oil. The system is a sealed unit. The breaking of any seal may be
dangerous, will damage the heater and will invalidate the warranty.
DO NOT use the heater for anything other than its intended purpose. It is designed for providing heat in enclosed areas, no smaller
than 4m³, such as offices, homes, workshops etc. It is not suitable for drying clothes or laundry.
DO NOT place the heater close to a bath, wash basin, shower, swimming pool or any other water-filled area or wet surface.
DO NOT get the heater wet or use in areas of high condensation.
DO NOT place the heater up against any surface such as a wall, door, furniture etc.
DO NOT place the heater immediately below any electrical outlet.
DO NOT move the heater whilst it is on, always disconnect from the supply and allow to cool first.
DO NOT allow the power lead to touch the radiator surface.
DO NOT cover the radiator or use it to dry laundry.
DO NOT store the electrical lead until the radiator is cold.
DO NOT attempt to repair a damaged heater, contact an authorised service agent.
DO NOT stand on the heater.
DO NOT touch the heating elements when the heater is on as it becomes very hot.
Operators must read this manual or receive adequate training before using the heater.
Children should be supervised at all times when the heater is in use.
Ensure that the heater is correctly turned off when not in use and store in a safe, dry area, out of reach of children.
© Jack Sealey Limited
INSTRUCTIONS FOR:
OIL FILLED RADIATOR MINI 800W/230V
6 ELEMENT
RD800
MODEL No:
Original Language Version
Recommended fuse rating 13amp
, are fitted with live (brown) and neutral (blue) wires only.
RD800
Issue: 1 - 19/05/14
Advertisement
Related Manuals for Sealey RD800
Summary of Contents for Sealey RD800
- Page 1 RD800 MODEL No: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 3. SPECIFICATION Model No: ....RD800 Power:......800W Supply:..