LG SH2 - Sound Bar Simple Manual

Also See for SH2:

Service manual (39 pages)

Owner's manual (28 pages)

Simple manual (4 pages)

Table of Contents

Contents

1 Introduction
2 Front Panel
3 Subwoofer Connection
4 Rear Panel
5 TV Connection
6 Additional Information
7 Remote control
8 Documents / Resources
- 8.1 References
- 8.2 Download manual

LG SH2 - Sound Bar Simple Manual

Introduction

Please read this manual carefully before operating your set and retain it for future reference.
To view the instructions of advanced features, visit http://www.lg.com and then download Owner's Manual.
Some of the content in this manual may differ from your unit.

Front Panel

Front Panel
- Selects Function
- Adjusts Volume
- Power On/Off

Subwoofer Connection

Place the subwoofer near the sound bar and follow steps below.

Press each plastic finger pad to open subwoofer terminals on the unit.
Connect the black stripe wire to the terminal marked - (minus) and the other end to the terminal (red tube) marked + (plus).

Rear Panel

SUB WOOFER (4Ω) - Connect to a Subwoofer
OPT. IN - Connect to an Optical device
PORT. IN - Connect to a Portable device

TV Connection

Connect the sound bar to the TV using Optical cable.
Set up [External Speaker (Optical)] on your TV setting menu.

Additional Information

Specification

Power requirements	Refer to the main label.
Power consumption	Refer to the main label.
Dimensions (W x H x D)	Approx. mm x 62 mm x 90 mm (34.6 inch x 2.4 inch x 3.5 inch)
Amplifier (Total RMS Output power)	W RMS

Design and specifications are subject to change without notice.

Remote control

Remote control
ASC/STANDARD/CINEMA : Selects sound effect.
*ASC: Adaptive Sound Control
DRC ON/OFF : Makes comfortable sound at Dolby Digital.
WOOFER LEVEL+/- : Adjusts the volume level of subwoofer.
AUTO POWER ON/OFF : Automatically turns on by an input source: Optical, Bluetooth, LG TV

Replacement of battery

Industry Canada Statement
[For having wireless function (WLAN, Bluetooth,...)] This device contains licence-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s).
Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3 (B)/NMB-3 (B)
IC Radiation Exposure Statement
[For having wireless function (WLAN, Bluetooth,...)]
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.8 inches) between the antenna & your body.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

[For product having the wireless function using 5 GHz frequency bands]

the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate; and
[for devices operating in the band 5250-5350 MHz having an e.i.r.p. greater than 200 mW] antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 of RSS-247 shall be clearly indicated.

Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.