Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HP MP9
Summary of Contents for HP MP9
- Page 1 Hardware Reference Guide HP MP9 Model 9000 Digital Signage Player...
- Page 2 HP End User Not all features are available in all editions License Agreement (EULA). If you do not The information contained herein is subject of Windows 8.
- Page 3 About This Book This guide provides basic information for upgrading the HP Digital Signage Player. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information.
- Page 4 About This Book...
-
Page 5: Table Of Contents
Table of contents 1 Product features ....................... 1 Standard configuration features ....................1 Front panel components MP9 Digital Signage Player ..............2 Rear panel components MP9 Digital Signage Player ..............3 Serial number location ......................3 2 Hardware upgrades ......................4 Serviceability features ....................... -
Page 7: Product Features
This computer model can be used in a tower orientation or a desktop orientation. The tower stand is sold separately. The MP9 Digital Signage player has the following mounting options: 100 mm x 100 mm Video Electronics Standards Association (VESA) mounting capability ●... -
Page 8: Front Panel Components Mp9 Digital Signage Player
Front panel components MP9 Digital Signage Player Drive configuration may vary by model. Some models have a bezel blank covering one or more drive bays. Dual-State Power Button USB 3.0 Port - Charging Hard Drive Activity Light Microphone/Headphone Connector USB 3.0 Port... -
Page 9: Rear Panel Components Mp9 Digital Signage Player
Rear panel components MP9 Digital Signage Player DisplayPort Monitor Connectors USB 3.0 Ports (blue) VGA Monitor Connector RJ-45 Network Connector Line-Out Connector for powered audio devices Power Cord Connector (green) Serial number location Each computer has a unique serial number and a product ID number that are located on the exterior of the computer. -
Page 10: Hardware Upgrades
To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper workstation, setup, posture, and health and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located on the Web at http://www.hp.com/ergo. WARNING! Energized and moving parts inside. -
Page 11: Connecting The Power Cord
Connecting the power cord When connecting the power supply, it is important to follow the steps below to ensure the power cord does not pull free from the computer. Plug the female end of the power cord into the power supply brick (1). Connect the other end of the power cord to an electrical outlet (2). -
Page 12: Removing The Computer Access Panel
Removing the computer access panel To access internal components, you must remove the access panel: Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as a USB flash drive, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. Disconnect the power cord from the power outlet and disconnect any external devices. -
Page 13: Replacing The Computer Access Panel
Changing from desktop to tower configuration The computer can be used in a tower orientation with an optional tower stand that can be purchased from HP. Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as a USB flash drive, from the computer. - Page 14 Orient the computer so that its right side is facing up and place the computer in the optional stand. NOTE: To stabilize the computer in a tower orientation, HP recommends the use of the optional tower stand. Reconnect the power cord and any external devices, then turn on the computer.
-
Page 15: Removing And Replacing A Hard Drive
Removing and replacing a hard drive NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as a USB flash drive, from the computer. - Page 16 Pull the release lever next to the rear of the hard drive outward (1). While pulling the release lever out, slide the drive back until it stops, then lift the drive up and out of the bay (2). To install a hard drive, you must transfer the silver and blue isolation mounting guide screws from the old hard drive to the new hard drive.
- Page 17 Align the guide screws with the slots on the chassis drive cage, press the hard drive down into the bay, then slide it forward until it stops and locks in place. Connect the hard drive power cable (1) and data cable (2) to the system board. Replace the access panel.
-
Page 18: Installing Additional Memory
Installing additional memory The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3- SDRAM) small outline dual inline memory modules (SODIMMs). SODIMMs The memory sockets on the system board can be populated with up to two industry-standard SODIMMs. -
Page 19: Populating Sodimm Sockets
Populating SODIMM sockets There are two SODIMM sockets on the system board, with one socket per channel. The sockets are labeled DIMM1 and DIMM3. The DIMM1 socket operates in memory channel B. The DIMM3 socket operates in memory channel A. Item Description System Board Label... -
Page 20: Installing Sodimms
Installing SODIMMs CAUTION: You must disconnect the power cord and wait approximately 30 seconds for the power to drain before adding or removing memory modules. Regardless of the power-on state, voltage is always supplied to the memory modules as long as the computer is plugged into an active AC outlet. Adding or removing memory modules while voltage is present may cause irreparable damage to the memory modules or system board. - Page 21 Disconnect the hard drive power cable (1) and data cable (2) from the system board. WARNING! To reduce risk of personal injury from hot surfaces, allow the internal system components to cool before touching. Pull the release lever next to the rear of the hard drive outward (1). While pulling the release lever out, slide the drive back until it stops, then lift the drive up and out of the bay (2).
- Page 22 To remove a SODIMM, press outward on the two latches on each side of the SODIMM (1) then pull the SODIMM out of the socket (2). Slide the new SODIMM into the socket at approximately a 30° angle (1) then press the SODIMM down (2) so that the latches lock it in place.
-
Page 23: Replacing The Battery
The lithium battery is only used when the computer is NOT connected to AC power. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, go to http://www.hp.com/... - Page 24 Locate the battery and battery holder on the system board. Depending on the type of battery holder on the system board, complete the following instructions to replace the battery. NOTE: You may need to use a small tool, such as tweezers or needle-nose pliers, to remove and replace the battery.
- Page 25 Pull back on the clip (1) and slide the replacement battery down into the holder (2). Type 2 Push the battery toward the outside of the chassis to release it from the holder and lift it out. Lower the battery so that is next to the holder then push it into the holder. Replacing the battery...
- Page 26 NOTE: After the battery has been replaced, use the following steps to complete this procedure. Replace the computer access panel. Plug in the computer and turn on power to the computer. Reset the date and time, your passwords, and any special system setups using Computer Setup. Lock any security devices that were disengaged when the computer access panel was removed.
-
Page 27: Installing A Security Lock
Installing a security lock The security locks displayed below and on the following pages can be used to secure the computer. Cable lock Padlock Installing a security lock... -
Page 28: Appendix A Electrostatic Discharge
● Use a portable field service kit with a folding static-dissipating work mat. ● If you do not have any of the suggested equipment for proper grounding, contact an HP authorized dealer, reseller, or service provider. NOTE: For more information on static electricity, contact an HP authorized dealer, reseller, or service provider. -
Page 29: Appendix B Computer Operating Guidelines, Routine Care And Shipping Preparation
Computer operating guidelines, routine care and shipping preparation Computer operating guidelines and routine care Follow these guidelines to properly set up and care for the computer and monitor: Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold. ●... -
Page 30: Shipping Preparation
Shipping preparation Follow these suggestions when preparing to ship the computer: Back up the hard drive files to an external storage device. Be sure that the backup media is not exposed to electrical or magnetic impulses while stored or in transit. NOTE: The hard drive locks automatically when the system power is turned off. -
Page 31: Index
Index access panel power cord connection 5 removal 6 product ID location 3 replacement 7 rear panel components battery replacement 17 digital signage player 3 removing battery 17 computer operating guidelines 23 computer access panel 6 hard drive 9 digital signage player MP9000 1 security cable lock 21...