Related Manuals for Dell SE2725H
Summary of Contents for Dell SE2725H
- Page 1 Dell SE2725H Monitor Teardown Instruction Regulatory Model: SE2725H Regulatory Type: SE2725Hc June 2024 Rev. A00...
- Page 2 A WARNING indicates a potential for property damage, personal injury, or death. © 2023 Dell Inc. or its subsidiaries. All rights reserved. Dell Technologies, Dell, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.
-
Page 3: Table Of Contents
Contacting Dell ........ -
Page 4: Safety Instructions
Safety Instructions Use the following safety guidelines to protect your monitor from potential damage and to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that you have read the safety information that shipped with your monitor. NOTE: Before using the monitor, read the safety information that is shipped with your monitor and printed on the product. -
Page 5: Disassembly And Reassembly
Disassembly and reassembly NOTE: This “Disassembly and Assembly Procedures” is for EMEA only, not for other regions. Please note that Dell will deem warranty void if any disassembly is done on the monitors. Recommended tools List the type and size of the tools that would typically can be used to disassemble the product to a point where components and materials requiring selective treatment can be removed. -
Page 6: Installing The Stand
Installing the stand Steps 1. Slide the tabs on the stand assembly into the slots on the monitor and press the stand assembly down to snap it into place. Next steps 1. Follow the procedure in After working inside your monitor. -
Page 7: Installing The Vesa Cover
Installing the VESA cover Steps 1. Press the VESA cover to install it to the back cover. Next steps Installing the stand. 2. Follow the procedure in After working inside your monitor. -
Page 8: Back Cover
Back cover Removing the back cover Prerequisites 1. Follow the procedure in Before working inside your monitor. 2.Removing the stand. 3.Removing the VESA cover. Steps 1. Remove four screws (M4x10) that secure the back cover to the chassis assembly. 2.Remove two screws (M3x6) that secure the back cover to the chassis assembly. 3. -
Page 9: Installing The Back Cover
Installing the back cover Steps 1. Place and snap the back cover into place the chassis assembly. NOTE: Align the screw holes on the back cover with the screw holes on the chassis assembly before applying slight pressuure to the back cover. - Page 10 2. Remove three screws (M2x2) on the keypad board.
-
Page 11: Installing The Keypad Board
Installing the keypad board Steps 1. Replace three screws (M2x2) to secure the keypad boardr to the monitor. 1. Connect keypad board cable to the connector on the main board. -
Page 12: Metal Frame
Next steps Installing the back cover. 2. Follow the procedure in After working inside your monitor. Metal frame Removing the metal frame Prerequisites 1. Follow the procedure in Before working inside your monitor. Removing the stand. Removing the VESA cover. Removing the back cover. -
Page 13: Installing The Metal Frame
Installing the metal frame Steps 1. Replace two screws (M3x2.5) on the two sides of metal frame. 2. Replace two screws (4-40unc) on the VGA port of metal frame. - Page 14 2. Replace three tapes on metal frame and Connect three cables to the connector on the panel and main board.
-
Page 15: Main Board And Power Board
Next steps Installing the back cover. 2. Follow the procedure in After working inside your monitor. Main board and power board Removing the main board and power board Prerequisites 1. Follow the procedure in Before working inside your monitor. Removing the stand. Removing the VESA cover. - Page 16 3. Remove four screws (D3x7) and one screw (M4X8) on the main board and power board. 3. Disconnect two cables from the connector on the main board and power board.
-
Page 17: Installing The Main Board And Power Board
Installing the main board and power board Steps 1. Connect two cables to the connector on the main board and power board. - Page 18 3. Replace four screws (D3x7) and one screw (M4X8) on the main board and power board.
- Page 19 Next steps Installing the metal frame. 2. Follow the procedure in After working inside your monitor...
-
Page 20: Contacting Dell
Contacting Dell To contact Dell for sales, technical support, or customer service issues, see www.dell.com/contactdell. NOTE: Availability varies by country, region, or product, and some services may not be available in your country. NOTE: If you do not have an active Internet connection, you can find contact information about your purchase invoice, packing slip,...