NEC VT560 Replacement Instructions Manual
Replacing in a 2000i-dvx
Hide thumbs
Also See for VT560:
- User manual (44 pages) ,
- Important information manual (38 pages) ,
- Control commands (9 pages)
Advertisement
Quick Links
Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX
This kit contains:
• an NEC VT560 projector
• a T20 TORX® security key
• a 7/16" nut driver
• 3 TORX button-head screws, flat washers and split
washers (if required)
• 3 spacers (if required)
• 4 replacement tie wraps
• a Projector Mount Location Guide
Use these instructions to replace the NEC VT560 projector in a 2000i-DVX. Note that you will reuse the screws, washers
and spacers that secure the original projector to the cabinet, so keep track of them. However, three replacement sets of
screws, washers and spacers are included in the kit.
To replace the NEC VT560 projector in a 2000i-DVX, complete the following tasks:
1. Remove the original projector (and projector plate) from the cabinet (this page).
2. Install the replacement projector in the cabinet (page 4).
3. Align the projected image (page 6).
4. Check projector settings (page 15).
CAUTION
Complete these procedures only with the assistance of another person, who must support the projector
while you remove the original projector and while you install the new one. Otherwise, the projector may
fall and sustain damage.
To remove the original projector
1. If you need better access to the rear of the cabinet, retract the anti-tip feet and unlock the wheels by raising the caster
tab locks on each wheel. Then roll the unit away from the wall. Press the caster tab locks down to lock the wheels
again, and then extend the anti-tip feet.
2. Using the height-adjustment handle, raise the unit to allow easier access to the projector.
3. Shut down the computer, and then press and hold the Lamp Off button in the Control Panel until the screen turns black
(approximately three seconds). Release the button and the projector lamp powers off in 60 seconds.
4. Unplug the 2000i from the power outlet.
99-00590-00 Rev A0
Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX
Tools required (but not supplied):
• small wire cutters for snipping tie wraps
• a 3/16" or 5/32" flat screwdriver (for adjusting focus)
Lamp Off Button
1 of 15
Advertisement
Related Manuals for NEC VT560
Summary of Contents for NEC VT560
- Page 1 • a Projector Mount Location Guide Use these instructions to replace the NEC VT560 projector in a 2000i-DVX. Note that you will reuse the screws, washers and spacers that secure the original projector to the cabinet, so keep track of them. However, three replacement sets of screws, washers and spacers are included in the kit.
- Page 2 CAUTION A second person must support the base of the projector during the entire removal process. Otherwise, the projector could fall and sustain damage. 2 of 15 Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX 99-00590-00 Rev A0...
- Page 3 Carefully collect them all and place them nearby, as you’ll need them when you install the replacement projector. Remove the projector and set it aside. 99-00590-00 Rev A0 Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX 3 of 15...
- Page 4 Flat Washer (x3) Projector Plate Spacer (x3) IMPORTANT Assemble the security screws, split washers and flat washers in the order shown in the figure above. 4 of 15 Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX 99-00590-00 Rev A0...
- Page 5 (with a gap of 3.5" or greater between the image and the top frame of the cabinet), you may need to raise the projector to a higher screw location. This adjustment is discussed in detail on page 9 (step 6). 99-00590-00 Rev A0 Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX 5 of 15...
-
Page 6: Aligning The Projected Image
You will notice that the image is about three inches lower than the screen frame. Perform the procedures that follow to slide the image up to the top of the screen, as well as make other minor image adjustments. 6 of 15 Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX 99-00590-00 Rev A0... - Page 7 3. Remove the plastic cap that covers the access hole. If the cap seems tight, carefully pry it off with a screwdriver, inserting the screwdriver into the small opening at the top of the cap. 99-00590-00 Rev A0 Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX 7 of 15...
- Page 8 The top of the screen image should be approximately 3–3.5" from the upper frame. If the gap at the top of the screen is less than 3.5", proceed directly to step 7. 8 of 15 Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX 99-00590-00 Rev A0...
- Page 9 7. Move to the front of the cabinet, and use the supplied 7/16" nut driver to turn the bolt inside the Electronics Tray access hole counterclockwise, adjusting the angle of the small mirror. This raises the image to meet the upper frame of the cabinet. 99-00590-00 Rev A0 Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX 9 of 15...
- Page 10 Move the projector backwards (away from the screen) until the image enlarges enough to fill the screen. c. Tighten the screws and washers you previously loosened. 10 of 15 Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX 99-00590-00 Rev A0...
- Page 11 Although the NEC VT560 User’s Manual tells you to use the blue focus ring to obtain the best image, you must disregard this information. Rather, use the zoom lever on the projector to adjust focus. This lever has been altered so that it adjusts image focus.
- Page 12 To adjust the image laterally (side-to-side) 1. Crouch behind the projector and look at the projected image through the view port. 12 of 15 Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX 99-00590-00 Rev A0...
- Page 13 While a second person supports the projector, use the security key to loosen and then remove the two button head screws in the letter locations only. 99-00590-00 Rev A0 Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX 13 of 15...
- Page 14 14 of 15 Replacing an NEC VT560 Projector (03-00060) in a 2000i-DVX 99-00590-00 Rev A0...
- Page 15 © 2004 SMART Technologies Inc. All rights reserved. SMART Board and the SMART logo are trademarks of SMART Technologies Inc. NEC is a trademark of NEC Corporation. Phillips is a registered trademark of Phillips Screw Company. All other third-party product and company names may be trademarks of their respective owners.