Page 1 SERVER LS2400 U s e r ' s G u i d e...
Page 3 SERVER LS2400 U s e r ' s G u i d e...
Page 4: Proprietary Notice And Liability Disclaimer
The information disclosed in this document, including all designs and related materials, is the valuable property of NEC Computer Systems Division (hereinafter "NEC CSD") and/or its licensors. NEC CSD and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use, and sales rights thereto, except to the extent said rights are expressly granted to others.
Page 5: Table Of Contents
Contents Proprietary Notice and Liability Disclaimer Using This Guide ................... ix Text Conventions.................... x Related Documents ..................xi Safety Notices ....................xii Safety Notices for Users Outside of the U.S.A. and Canada ....xiii Care and Handling ..................xiv System Overview ..........1-1 Overview......................1-2 System Chassis ...................1-4 Power Supply....................1-5...
Page 6 BIOS Setup Configuration Settings ............. 3-4 Main Menu ..................3-5 Primary IDE Master and Slave Submenu........3-6 Secondary IDE Master and Slave Submenu......3-7 Keyboard Submenu ..............3-8 Processor Settings Submenu ............ 3-8 Advanced Menu .................. 3-9 PCI Configuration Submenus ........... 3-10 PCI Device, Slot 1 - Slot 4 Submenus ........
Page 7 Installing the Pentium II Processor (S.E.C. Version) ....4-10 Replacing the Pentium III Processor (SECC2 Version) ....4-12 DIMMs ....................4-14 Memory DIMM Configurations ..........4-15 Installing DIMMs..............4-16 Removing DIMMs ..............4-17 Option Boards ...................4-18 Installation Considerations ...............4-18 Controller/Adapter Hardware Configurations ........4-18 Installing an Option Board ..............4-19 Removing an Option Board..............4-21 Hard Disk Drives ..................4-22...
Page 8 System Cabling ............A-1 Before You Begin..................A-2 Static Precautions ..................A-2 Standard Configuration ................A-3 RAID Configuration..................A-6 SecuRAID 100 (AMI MegaRAID EXPRESS 762) RAID Controller ..A-6 SecuRAID 110 or 210 (Mylex AcceleRAID 150 or 250) RAID Controller ................... A-6 System Setup Utility ..........B-1 System Setup Utility (SSU)................
Page 9 Glossary Equipment Log Index xxxx Contents vii...
Page 11: Using This Guide
Using This Guide The LS2400 User’s Guide provides a quick reference to information about your system. Its goal is to familiarize you with your system and the tasks necessary for system configuring and upgrading. This guide contains the following information: Chapter 1, “System Overview”...
Page 12: Text Conventions
Text Conventions This guide uses the following text conventions. Warnings, cautions, and notes have the following meanings: WARNING Warnings alert you to situations that could result in serious personal injury or loss of life. ! CAUTION Cautions indicate situations that can damage the system hardware or software.
Page 13: Related Documents
Related Documents In addition to this guide, the following system documentation is included with your server either as electronic files on E or as paper XPRESS UILDER copy shipped with your server. System Release Notes Release Notes provide you with the latest information about your system.
Page 14: Safety Notices
Safety Notices Caution: To reduce the risk of electric shock which could cause personal injury, follow all safety notices. The symbols shown are used in your documentation and on your equipment to indicate safety hazards. Warning: Lithium batteries can be dangerous. Improper handling of lithium batteries may result in an explosion.
Page 15: Safety Notices For Users Outside Of The U.s.a. And Canada
Safety Notices for Users Outside of the U.S.A. and Canada PELV (Protected Extra-Low Voltage) Integrity: To ensure the extra- low voltage integrity of the equipment, connect only equipment with mains-protected electrically-compatible circuits to the external ports. Remote Earths: To prevent electrical shock, connect all local (individual office) computers and computer support equipment to the same electrical circuit of the building wiring.
Page 16: Care And Handling
Care and Handling Use the following guidelines to properly handle and care for your system. Protect the system from extremely low or high temperatures. Let the system warm (or cool) to room temperature before using it. Keep the system away from magnetic forces. Keep the system dry.
Page 17: System Overview
System Overview Overview System Chassis Power Supply Peripheral Bays Diskette Drive System Board Features System Security...
Page 18: Overview
Overview This server is a modular, multiprocessing server based on the Intel Pentium® chip set. The combination of compute performance, memory capacity, and integrated I/O provides a high performance environment for many server market applications. These range from large corporations supporting remote offices to small companies looking to obtain basic connectivity capability such as file and print services, e- mail, web access, web site server, etc.
Page 19 As application requirements increase, you can expand your server with an additional processor, additional memory, add-in boards and peripheral devices: tape devices, CD-ROM, diskette drives and hard disk drives. Your server features the following major components: Single or dual high-performance Pentium processors packaged in either Single Edge Contact (SEC) cartridge or Single Edge Contact Cartridge Version 2 (SECC2) connectors.
Page 20: System Chassis
System Chassis The system chassis is an easy-to-expand, fabricated metal structure. The major system components are shown in this illustration. System Chassis Removable Media Bays (3) 1.44 MB 3.5" diskette drive System Board Speaker Power supply Disk Drive Bays (4) Fan (behind disk drive bays) 1-4 System Overview...
Page 21: Power Supply
Power Supply The 260 watt power supply is switch-selectable for 115 or 230 Vac at an operating frequency of 50/60 Hz. It is designed to comply with existing emissions standards and provides sufficient power for a fully loaded system configuration. The power supply voltage selection switch is factory set to 115Vac for systems used in the United States;...
Page 22: System Board Features
System Board Features The system board offers a “flat” design with the processor and memory subsystems residing on the board. This figure shows the major components on the system board. The following subsections describe the system board major components. Pri. Sec.
Page 23: Pentium Processor
Pentium Processor Depending on system configuration, each system includes one or two Pentium processors. Each Pentium processor is packaged in a Single Edge Contact (S.E.C.) cartridge or Single Edge Contact Cartridge Version 2 (SECC2.). The cartridge includes the processor core with an integrated 16 KB primary (L1) cache;...
Page 24: I/O Expansion Slots
I/O Expansion Slots The server's expansion capabilities meet the needs of file and application servers for high performance I/O by providing a combination of PCI local bus and ISA connectors. The system board has two full-length ISA bus connectors. One of the connectors share a chassis expansion slot with a PCI connector.
Page 25: Real-Time Clock/Calendar
Real-Time Clock/Calendar The real-time clock provides system clock/calendar information stored in a non-volatile memory (NVRAM). The real-time clock battery provides power backup for the real-time clock. BIOS A BIOS and Setup Utility are located in the Flash EPROM on the system board and include support for system setup and PCI/ISA Plug-and-Play auto-configuration.
Page 26: Scsi Controller
SCSI Controller The system board includes a Symbios Logic SYM53C875 embedded dual-function, PCI SCSI host adapter. The SYM53C875 contains two independent SCSI controllers that share a single PCI bus master interface. Internally, each controller is identical, capable of operations using either 8- or 16-bit SCSI providing 10 MB/s (Fast-10) or 20 MB/s (Fast-20) throughput, or 20 MB/s (Ultra) or 40 MB/s (Ultra-wide) throughput.
Page 27: Peripheral Controller
Peripheral Controller The advanced integrated peripheral controller supports two serial ports, one parallel port, diskette drive, PS/2-compatible keyboard and mouse, and integrated Real Time Clock (RTC). The system provides the connector interface for each port. Serial Ports Both serial ports are relocatable. Each serial port can be set to one of four different COM ports and can be enabled separately.
Page 28: System Security
System Security To help prevent unauthorized entry or use of the system, the system includes a physical padlock loop and Server Management software that monitors the system intrusion switch. Security with Mechanical Locks and Monitoring A lock may be installed at the rear of the system to prevent removal of the side cover.
Page 29: Setting Up The System
Setting Up the System Selecting a Site Unpacking the System Getting Familiar with the System Making Connections Setting the Line Voltage Connecting the Power Cord Powering On Your System...
Page 30: Selecting A Site
Selecting a Site The system operates reliably in a typical office environment. Choose a site that is: Near grounded, three-pronged power outlets. Note: For the United States and Canada, this means a NEMA 5-15R outlets for 100-120 VAC or NEMA 6-15R outlets for 200-240 VAC.
Page 31: Unpacking The System
Unpacking the System WARNING Your system weighs approximately 38 pounds (17.2 kg). If your system contains numerous optional boards and peripheral devices, it will weigh more. To avoid personal injury, make sure you have someone help you lift or move the system.
Page 32: Getting Familiar With The System
Getting Familiar with the System Before setting up your system, you should become familiar with the system’s features, such as the location of your system's front and rear panel switches, indicators and connectors, etc. Front View This figure shows the location of the front system controls and indicators.
Page 33: Rear View
Rear View This figure shows the location of the following rear system controls and indicators. 115V Rear Features and Controls AC input power connector Supplies AC power to the power supply. Line voltage selector switch Selects AC input power of 115 VAC or 230 Keyboard PS/2-compatible 6-pin mini-DIN connector.
Page 34: Making Connections
Making Connections If your system normally operates without a video display or keyboard (for example, as a network server), you must install a video display and keyboard to configure the system. You may remove them after running the System Setup Utility (SSU). For information on running the SSU, refer to Appendix B of this User’s Guide.
Page 35 115V Rear Panel Connections Keyboard PS/2-compatible 6-pin mini-DIN connector. Mouse PS/2-compatible 6-pin mini-DIN connector. COM1 COM1 serial port 9-pin connector. VGA monitor 15-pin connector. Network Connector RJ-45 connector Printer 25-pin parallel port connector. COM2 Remoted COM2 serial port 9-pin connector. USB Connectors Two remoted USB Connectors.
Page 36: Setting The Line Voltage
Setting the Line Voltage The system contains a 260 watt power supply that is switch-selectable for 115 or 230 VAC at an operating frequency of 50/60Hz. The power supply voltage selection switch is factory set to 115Vac for systems used in the United States; it is set to 230Vac for systems used in Europe.
Page 37 115V 115V 115V 230V Setting the Line Voltage Voltage selector switch set to 115 VAC Voltage selector switch set to 230 VAC Setting Up the System 2-9...
Page 38: Connecting The Power Cord
Connecting the Power Cord Plug the female end of the AC power cord into the input receptacle on the rear of the power supply cage. Plug the male end of the power cord into NEMA 5-15R outlet for 100-120 VAC or NEMA 6-15R outlet for 200-240 VAC.
Page 39: Powering On Your System
Powering On Your System Power on your system as follows. 1. Make sure all external devices, such as a video display, keyboard, and mouse (optional) have been connected, and the power cords are connected. 2. Power on the video display and any other external devices. 3.
Page 41: Configuring Your System
Configuring Your System Configuring Your System BIOS Setup Utility Symbios Configuration Utility Optional RAID Controller Configuring System Board Jumpers...
Page 42: Configuring Your System
Configuring Your System Configuration and setup utilities are used to change your system configuration. You can configure your system, as well as option boards you may add to your system, using the BIOS Setup Utility. Several unique system parameters are configured using the BIOS Setup, which is stored in the system FLASH memory.
Page 43: Bios Setup Utility
BIOS Setup Utility The BIOS Setup Utility is used to change system configuration parameters. This utility has some unique parameters and many parameters that are also configurable with the SSU. The utility is resident in the system FLASH memory and does not require a diskette or an operating system present to run.
Page 44: Bios Setup Configuration Settings
Function in Setup Menu F1 or Alt-H Get Help about an item. Exit the current menu and return to the previous menu. Left or right arrow Move between menus. keys Up or down arrow Move cursor up and down. The cursor moves only keys to the settings that you can change.
Page 45: Main Menu
Main Menu Feature Choices Description Your Setting System Time HH:MM:SS Sets the system time. System Date MM/DD/YYYY Sets the system date. Legacy Diskette A: Disabled Selects the diskette type. 360KB The 1.25 MB diskette requires 1.2 MB a 3-mode diskette drive. 720KB 1.44/1.25 MB 2.88 MB...
Page 46: Primary Ide Master And Slave Submenu
Primary IDE Master and Slave Submenu Feature Choices Description Your Setting Type Auto allows the system to Auto attempt auto-detection of the drive type. None None informs the system to ignore this drive. CD-ROM CD ROM allows the manual entry of fields described below.
Page 47: Secondary Ide Master And Slave Submenu
Secondary IDE Master and Slave Submenu Feature Choices Description Your Setting Type Auto Auto allows the system to attempt auto-detection of the drive type. None None informs the system to ignore this drive. CD-ROM CD ROM allows the manual entry of fields described below.
Page 48: Keyboard Submenu
Keyboard Submenu Feature Choices Description Your Setting NumLock Selects power-on state for Num Lock. Key Click Enables or disables key Disabled Enabled click. Keyboard auto- 13.3/sec 30/sec Selects key repeat rate. repeat rate 10/sec 26.7/sec 6/sec 21.8/sec 2/sec 18.5/sec Keyboard auto- 1/4 sec Selects delay before key repeat delay...
Page 49: Advanced Menu
Advanced Menu Feature Choices Description Your Setting Installed OS Other Select the operating system Win95 installed in your system. Reset Configuration Select Yes if you want to Data clear the extneded system configuration data (ESCD) area during next boot. System automatically resets to No in next boot.
Page 50: Pci Configuration Submenus
PCI Configuration Submenus This submenu should only be changed by qualified technical personnel. ! CAUTION Leave PCI Configuration Submenu at factory-default settings. This submenu should only be changed by a technically qualified person. PCI Configuration Submenu Feature Choices Description Your Setting PCI Device, Press ENTER.
Page 51: Integrated Peripheral Configuration Submenu
Integrated Peripheral Configuration Submenu Feature Choices Description Your Setting COM 1: Disabled Auto forces BIOS to configure the port. Enabled (Serial Port A) Auto OS Controlled forces OS to OS Controlled configure the port. If this COM port is used for Console Redirection make sure I/O and IRQ are identical to the values in...
Page 52: Advanced Chipset Control
Advanced Chipset Control Feature Choices Description Your Setting 640 – 768K Disabled If enabled, ISA Master and DMA cycles are forwarded Enabled to PCI. Delayed Disabled Enable the delayed Transaction transaction mechanism Enabled when PIIX4 is target of a PCI transaction. Passive Release Disabled Enable the Passive Release...
Page 53: Security Menu (Continued)
Security menu (Continued) Feature Choices Description Your Setting Set Supervisor Press ENTER When the <Enter> key is Password pressed, the user is prompted for a password; press ESC key to abort. Once set, this can be disabled by setting it to a null string, or by clearing password jumper on system board (refer to...
Page 54: Server Menu
Security menu (Continued) Feature Choices Description Your Setting Video Blanking Disabled Blank video when secure Enabled mode is activated. The user must enter a password to unlock the system. Cannot be enabled unless at least one password is enabled. Floppy Write When secure mode is Disabled Protect...
Page 55: System Management Submenu
System Management Submenu Feature Choices Description Your Setting System Event Disabled When enabled,.BIOS and Logging BMC will log system Enabled events. Clear Event Log Yes clears the system Event log. Sever Press ENTER Refer to “System Management Management Info Info Submenu.”...
Page 56: Server Management Information Submenu
Server Management Information Submenu The user cannot modify any items on this menu. If items require changes, consult your system administrator. Feature Choices Description Your Setting Board Part Information field only Number Board Serial Information field only Number System Part Information field only Number System Serial...
Page 57: Console Redirection Submenu
Console Redirection Submenu Feature Choices Description Your Setting COM Port When enabled, console Disabled Address redirection uses the I/O port specified. Make sure these values are identical to those of serial port A and B in the Peripheral Configuration Setup Menu. IRQ # None When console redirection...
Page 58: Boot Device Priority Submenu
Boot Device Priority Submenu Use the up or down arrow keys to select a device, then press the <+> or <-> keys to move the device higher or lower in the boot priority list. Boot Device Priority Submenu Boot Priority Device Description Your Setting...
Page 59: Exit Menu
Exit Menu You can make the following selections on the Exit Menu. Select an option using the up or down arrow keys, then press <Enter> to execute the option. Pressing <Esc> does not exit this menu. You must select one of the items from the menu or menu bar to exit.
Page 60: Symbios Configuration Utility
Symbios Configuration Utility The Symbios Configuration Utility detects the two SCSI host adapters located on the system board. Use the utility to: Change adapter and SCSI device default values Check and/or change SCSI device settings that may conflict with those of other devices in the server. Perform low-level formatting or verify operations on SCSI disk drives.
Page 61: Changing The Adapter And Device Configurations
The following keys are active for all SCSI Configuration screens: Action Arrows Up and down arrows move from one parameter to another within a screen. ENTER Displays options for a configurable parameter. Selects an option. Moves back to previous screen or parameter or EXIT if at the Main menu.
Page 62 To change device configuration parameters, perform the following steps: 1. At the SCSI Configuration Utility Main Menu, select the adapter which connects to the SCSI device you are reconfiguring. The first adapter listed controls the operation of the hard disk drives; the second adapter controls any SCSI removable media devices installed in your system.
Page 63 SYM53C875 Adapter 2 – SCSI Removable Media Devices Description Recommended Setting Your Configuration or Display Only Dev0 Dev1 Dev2 Dev3 Device Selections Press ENTER for menu. Select device and press ENTER. Sync Rate Width (bits) Disconnect Read/Write I/O timeout (secs) Scan for device at boot time Scan for SCSI LUNS Queue Tags...
Page 64: Optional Raid Controllers
Optional RAID Controllers One of the options available for your system is a RAID controller. The RAID controller gives your system the added security of fault tolerance. Two RAID controllers are available for use in your system: Mylex AcceleRAID 150 (SecuRAID 110) Controller Mylex AcceleRAID 250 (SecuRAID 210) Controller Mylex AcceleRAID Controller Factory Installed Controller...
Page 65: Add-On Controller
Add-on Controller If you are adding the Mylex AcceleRAID controller to an existing system, the AcceleRAID BIOS Configuration Utility allows you to configure disk arrays and logical drives in your system. Since the utility resides in the AcceleRAID BIOS on the RAID controller, its operation is independent of the operating system in your server.
Page 66: Configuring System Board Jumpers
Configuring System Board Jumpers Before You Begin Only a qualified technical person should perform the procedures in this section. ! CAUTION Electrostatic discharge (ESD) can damage the system board. Modify the system board only at an ESD workstation. Otherwise, wear an antistatic wrist strap attached to chassis ground.
Page 67 System Board Jumper Summary Jumper Function Pins (default in What it does at system reset bold) CMOS clear 1-2, Protect Preserves the contents of NVRAM. 2-3, Erase Replaces the contents of NVRAM with the manufacturing default settings. Password clear 5-6, Protect Maintains the current system password.
Page 68: Moving System Board Jumpers
Moving System Board Jumpers ! CAUTION Before doing the procedures in this section, make sure that your system is powered off and unplug the AC power cord from the back of the chassis. Failure to disconnect power before moving the jumpers can result in personal injury and equipment damage.
Page 69: Resetting The Cmos Nvram
Resetting the CMOS NVRAM To reset the CMOS NVRAM: 1. Power down the your system. Remove the left side panel as described in Chapter 4 of this User’s Guide. 2. Move the CMOS Clear jumper from pins 1-2 to pins 2-3. Refer to “Configuring System Board Jumpers”...
Page 70: Recovering The Bios
Recovering the BIOS This procedure should only be performed by qualified technical personnel. ! CAUTION Leave Recovery Boot jumper at factory-default setting. This jumper should only be moved by a technically qualified person. Boot Block Write Protect The jumper at pins 13, 14, and 15 controls whether the BIOS boot block is protected from being erased and reprogrammed.
Page 71: Chassis Intrusion Detection Jumper
All failures are logged to the system event log. The system will remember all FRB errors and display them at the end of POST until you select the Processor Retest option from the BIOS Setup utility. ! CAUTION For normal operation leave FRB Timer Enable jumper at factory-default setting.
Page 72: Bmc Forced Update Mode
BMC Forced Update Mode ! CAUTION Leave BMC Forced Update Mode jumper at factory-default setting: Setting this jumper incorrectly will prevent the system from booting. Programming should only be done by a technically qualified person. Contact your dealer or sales representative for more information.
Page 73: Upgrading Your System
Upgrading Your System Static Precautions Preparing Your System for Upgrade Equipment Log Removing a Side Panel Installing a Side Panel Modifying the System Board Option Boards Hard Disk Drives Front Panel Removing EMI Shields and Filler Panels Removable Media Devices...
Page 74: Static Precautions
WARNING The DC push-button on/off switch on the front panel does not turn off the system AC power. Also, +5vdc is present on the system board whenever the AC power cord is connected between the system and an AC outlet. Before doing the procedures in this manual, make sure that your system is powered off and unplug the AC power cord from the back of the chassis.
Page 75: Preparing Your System For Upgrade
Preparing Your System for Upgrade Depending on the upgrade, you will need one or more of the following tools: Phillips screwdriver (#1 bit and #2 bit) Flat-head screwdriver Small needle nose pliers Pen or pencil ESD workstation or antistatic wrist strap (recommended) Equipment Log Use the equipment log form located at the end of this manual to record the model and serial number of your system, all installed options, and...
Page 76: Removing A Side Panel
Removing a Side Panel To install options in your system, you must remove the side panel on the left side of the system (as viewed from the front). The side panel on the right side of the system (as viewed from the front) only has to be removed when adding removable media devices.
Page 77: Installing A Side Panel
Removing a System Side Panel Installing a Side Panel 1. Before replacing the side panel, make sure no tools or loose parts have been left inside the system chassis. 2. Make sure all option boards are firmly seated in their respective slots and that all interior cables are properly connected.
Page 78: Modifying The System Board
Modifying the System Board The following sections provide procedures for upgrading and configuring the system board in your system. Topics covered include: Replacing the real-time clock battery Replacing a Pentium processor Installing or removing DIMMs. ! CAUTION Electrostatic discharge (ESD) can damage add-in boards and other components;...
Page 79 OM06416 Replacing the Real-Time Clock Battery 1. Power off the system and remove the left side panel as described earlier in this chapter. 2. Insert the tip of a small flat-bladed screwdriver, or equivalent, under the plastic tab on the San-in plastic retainer (A in figure). 3.
Page 80: Replacing A Pentium Processor
Replacing a Pentium Processor This subsection provides the procedure for replacing (removing/installing) a Pentium II or Pentium III Processor in your system. The procedures cover upgrading and configuring the Pentium II Processor in your system. The system board has sockets for two processors.
Page 81: Removing The Pentium Ii Processor (S.e.c. Version)
Removing the Pentium II Processor (S.E.C. Version) WARNING If the system has been running, any processor and heat sink already installed on the board will be hot. To avoid the possibility of a burn, let the components cool for 10 minutes before continuing with the procedures described here.
Page 82: Installing The Pentium Ii Processor (S.e.c. Version)
Installing the Pentium II Processor (S.E.C. Version) 1. Power off the system and remove the left side panel as described earlier in this chapter. ! CAUTION Observe static precautions. Use an antistatic wrist strap. Hold the processor only by its edges. 2.
Page 83 8. Install the two clips that secure the heat sink to the processor. Assembling the Pentium II Processor 9. Position the processor so that the heat sink faces the center of the system board. Slide the processor into the retention module. Ensure that the alignment notch on the bottom of the cartridge fits into the plug in slot.
Page 84: Replacing The Pentium Iii Processor (Secc2 Version)
Replacing the Pentium III Processor (SECC2 Version) Note: The SECC2 processor has an active heat sink that includes a cooling fan. ! CAUTION Observe the safety and ESD precautions while performing these procedures. 1. Power off the system and remove the left side panel as described earlier in this chapter.
Page 85 8. Remove the new processor from its antistatic package and place it on a grounded, static-free surface or conductive foam pad.. 9. Position the processor into the URM. Ensure that the alignment notch on the bottom of the cartridge fits into the connector key in the slot (A). Push down firmly, with even pressure on both sides of the top until the cartridge is seated.
Page 86: Dimms
DIMMs The system board contains four DIMM sockets labeled 1 through 4. Each socket can hold a single 72-bit DIMM module with 32MB, 64MB, 128MB, or 256MB of memory. When all four sockets are populated, the system board supports a maximum of 1 GB of memory with 256MB DIMMs.
Page 87: Memory Dimm Configurations
Memory DIMM Configurations This table lists the distribution of DIMMs for specific memory configurations. System Capacity Capacity per DIMM slot (MB) Any DIMM Slot Order (MB) Slot 1 Slot 2 Slot 3 Slot 4 1024 Upgrading Your System 4-15...
Page 88: Installing Dimms
Installing DIMMs 1. Power off the system and remove the left side panel as described earlier in this chapter. ! CAUTION Observe static precautions. Use an antistatic wrist strap. Hold DIMMs only by their edges. 2. Holding the DIMM module only by the edges, remove it from its antistatic package.
Page 89: Removing Dimms
Removing DIMMs ! CAUTION Use extreme care when removing a DIMM. Too much pressure can damage the socket slot. Apply only enough pressure on the plastic ejector levers to release the DIMM 1. Power off the system and remove the left side panel as described earlier in this chapter.
Page 90: Option Boards
Option Boards This section describes how to install and remove ISA and PCI option boards. The system board has two ISA bus expansion slots and four PCI bus expansion slots. One of the ISA connectors shares a chassis expansion slot with a PCI connector. The high-performance PCI local bus allows the adoption of newer networking technology, such as 100 M/second Ethernet NICs, with a minimum of effort and without concern for I/O bottlenecks.
Page 91: Controller/Adapter Hardware Configurations
Controller/Adapter Hardware Configurations This table lists the option boards you may add to your system that require specific installation slots and provides information on memory and I/O addressing and assigned interrupt request number (IRQ). Option Board Hardware Configurations Memory Option Slot Option Board Address Address...
Page 92 6. Refer to the documentation accompanying the option board for information on whether the board is a PCI or ISA board. Refer to “Option Board Hardware Configurations” table to determine the recommended option board slot assignment and configuration parameters. Note: If you are adding a non-Plug and Play Legacy ISA option board, run the SSU before installing the board.
Page 93: Removing An Option Board
Removing an Option Board Note: Expansion slot covers must be installed on all vacant slots to maintain the electromagnetic emissions characteristics of the system and to assure proper cooling of the system components. 1. Power off the system and remove the left side panel as described earlier in this chapter.
Page 94: Hard Disk Drives
Hard Disk Drives Your system supports a variety of SCSI hard disks. Contact your sales representative or dealer for a list of approved devices. The internal hard disk drives are located in the 3.5-inch drive bay (A). 3.5-Inch Drive Bay Locations If you are adding or removing a SCSI hard disk device, consider the following: The system uses single-ended SCSI host adapters and supports...
Page 95: Installing An Internal Hard Disk Drive
Installing an Internal Hard Disk Drive 1. Power off the system and remove the left side panel as described earlier in this chapter. ! CAUTION Observe static precautions. Use an antistatic wrist strap. 2. Remove the 3.5-inch hard disk drive from its protective wrapper. Record the drive model and serial number in the equipment log.
Page 96 Removing the Disk Drive Bay 9. Replace the 3.5-inch drive bay. Insert the tabs into their slots on the chassis. Slide the drive bay towards the bottom of the chassis until the tabs hit their stops. 10. Connect the signal and power cables to the drives. All device power cables are labeled and must be installed in specific locations as shown below: Drive Location...
Page 97: Removing An Internal Hard Disk Drive
Cabling the Disk Drives Removing an Internal Hard Disk Drive 1. Power off the system and remove the left side panel as described earlier in this chapter. 2. Disconnect the signal and power cables from the back of the drive. It is necessary to completely remove the cables from all the drives before the drive can be removed.
Page 98: Front Panel
Front Panel The plastic front panel assembly is a one piece assembly. The appropriate removable filler panels are attached to the corresponding EMI shields. If you are installing peripheral devices in the external bays above the 3.5-inch floppy disk drive, you must remove the front cover along with the corresponding filler panel and EMI shield.
Page 99: Installing The Front Panel
Installing the Front Panel 1. Align the front panel tabs with the slots in the front of the chassis. 2. Press the front panel onto the front of the system chassis until the tabs snap into their slots. 3. Install the side panels as described earlier in this chapter. 4.
Page 100: Removing Emi Shields And Filler Panels
Removing EMI Shields and Filler Panels 1. Power off the system and remove the front panel as described earlier in this chapter. 2. Locate the EMI (Electromagnetic Interference) shield and filler panel covering the bay into which you are installing a peripheral device. The filler panel is released by pressing on its sides and removing it from the slots in the EMI shield.
Page 101: Removable Media Devices
Removable Media Devices A variety of IDE and SCSI removable media devices can be installed in peripheral bays A, B, and C. An IDE CD-ROM is always mounted in bay C. A 3.5-inch diskette drive is always mounted in bay D. Other devices should be installed in the first available bay from the top (bay A).
Page 102: Installing A 5.25-Inch Device
Your system includes two Symbios SYM53C875 independent SCSI controllers. Controller A attaches to a 68-pin 16-bit (wide) SCSI connector interface capable of supporting a maximum of four 1-inch high SCSI Ultra-wide hard disk drives or three 1.6-inch high SCSI Ultra-wide hard disk drives. Controller B attaches to a 50-pin 8-bit (narrow) SCSI connector interface capable of supporting three 5.25- inch removable SCSI media devices.
Page 103 Note: If the drive comes with drive rails, do not use them. Remove any rails already attached. 5. Slide the drive into the bay until the screw holes line up. It may be necessary to temporarily loosen the mounting screws on the already installed drives to position the new drive.
Page 104: Removing A 5.25-Inch Device
Removing a 5.25-Inch Device 1. Power off the system and remove the side panels as described earlier in this chapter. 2. Remove the front panel as described earlier in this chapter. 3. Disconnect the power cable (A) and ribbon data cable (B) from the device you are removing.
Page 105: 5-2 Problem Solving
Problem Solving Static Precautions Troubleshooting Checklists Additional Troubleshooting Procedures Specific Problems and Corrective Actions Problems with the Network PCI Installation Tips BIOS User’s Information...
Page 106 This chapter helps you identify and solve problems that may occur during system installation or while using your system. The first section of this chapter tells you how to reset your system in the event of problems. The next few sections provide troubleshooting checklists and procedural steps that help you isolate specific system problems.
Page 107: Static Precautions
Static Precautions An electrostatic discharge (ESD) can damage disk drives, option boards, and other components. You can provide some ESD protection by wearing an antistatic wrist strap attached to chassis ground when handling system components. Electronic devices can be easily damaged by static electricity. To prevent damage, keep them in their protective packaging when they are not installed in your system.
Page 108: Running New Application Software
Is the operating system properly loaded? Refer to the operating system documentation. Are all drivers properly installed? For information about installing drivers, refer to your Network Operating System Configuration Guide. Are the configuration settings in BIOS Setup and the System Setup Utility (SSU) correct? For information about running these utilities, refer to the “Configuring Your System”...
Page 109: After System Has Been Running Correctly
After System Has Been Running Correctly Problems that occur after the system hardware and software have been running correctly often indicate equipment failure. However, many situations that are easy to correct can also cause such problems. If you have problems after the system has been running correctly, check the following: If you are running the software from a diskette or CD-ROM, try a new copy of the software.
Page 110: Preparing The System For Diagnostic Testing
Preparing the System for Diagnostic Testing To prepare the system for diagnostic testing, perform the following: Note: Before disconnecting any peripheral cables from the system, turn off the system and any external peripheral devices. Failure to do so can cause permanent damage to the system and/or the peripheral devices.
Page 111: Monitoring Post
Monitoring POST Each time you turn on the system, the Power-On Self-Test (POST) runs automatically and checks the system board, processor board, memory, keyboard, and most installed peripheral devices. During the memory test, POST displays the amount of memory that it is able to access and test.
Page 112: Verifying Proper Operation Of Key System Indicators
POST Keys and Errors Action/Message Description If POST Beeps Before Initialization failed before video initialized. Most beep Video Appears code errors are fatal; initialization cannot continue. Refer to the section “BIOS User’s Information” in this chapter. If Monitor Displays Note error; press F1 to continue boot or F2 to enter Error Setup.
Page 113: Specific Problems And Corrective Actions
Specific Problems and Corrective Actions This section provides possible solutions for the following specific problems: Power LED does not light No beep or incorrect beep pattern No characters appear on screen Characters on the screen appear distorted or incorrect System cooling fan does not rotate Diskette drive activity LED does not light Hard disk drive activity LED does not light CD-ROM drive activity LED does not light...
Page 114: No Characters Appear On Screen
No Characters Appear on Screen Check the following: Is the keyboard working? Check to see if the Num Lock light is functioning. Is the video display monitor plugged in and turned on? Are the brightness and contrast controls on the video monitor properly adjusted? Are the video monitor switch settings correct? Is the video monitor signal cable properly installed?
Page 115: System Cooling Fan Does Not Rotate
System Cooling Fan Does Not Rotate Note: The system has a cooling fan module behind the hard disk drives. In addition, there is a cooling fan that is an integral part of the power supply. There are no serviceable components inside the power supply. If the power supply is opened, the manufacturer's warranty is voided.
Page 116: Hard Disk Drive Activity Led Does Not Light
Hard Disk Drive Activity LED Does Not Light If you have installed one or more hard disk drives in your system, check the following: Are the power and signal cables to the drive properly installed? Are all relevant switches and jumpers on the hard drive and adapter board set correctly? Is the hard disk drive properly configured in the SSU? Run the SSU to make sure that the hard disk drive is configured with the...
Page 117: Cd-Rom Drive Activity Light Does Not Light
CD-ROM Drive Activity Light Does Not Light Check the following: Is the power and signal cable to the CD-ROM drive properly installed? Are all relevant switches and jumpers on the drive set correctly? Is the drive properly configured? Is the onboard IDE controller enabled? Note: Front panel hard disk LED indicates IDE and SCSI devices : The hard disk drive activity light on the front panel lights when either an IDE hard disk drive, or a SCSI device controlled by...
Page 118: Enable F2 Prompt By Using Ssu
Enable F2 Prompt by Using SSU 1. Insert your SSU diskette in the diskette drive. This is the diskette that is created by copying the SSU software from E CD-ROM that XPRESS UILDER comes with the system. 2. Reboot the system by pressing Ctrl+Alt+Del while at the DOS operating system prompt or by pressing the reset switch.
Page 119: Enable F2 Prompt By Changing A Jumper And Using Ssu
Enable F2 Prompt by Changing a Jumper and Using SSU If you do not have an SSU diskette or CD available, you can clear CMOS memory to enable the F2 prompt. This means you must change a jumper on the system board, run the SSU, save your changes, and change the jumper back to the default setting.
Page 120: Bootable Cd-Rom Is Not Detected
Bootable CD-ROM Is Not Detected Check the following: Is the BIOS set to allow the CD-ROM to be the first bootable device? Check your BIOS Setup (F2) configuration. Problems with the Network The server hangs when the drivers are loaded: Change the PCI BIOS interrupt settings.
Page 121: Pci Installation Tips
The network driver files may be corrupt or deleted. Delete and then reinstall the drivers. Run the diagnostics. PCI Installation Tips Some common PCI tips are listed here. Reserve interrupts (IRQs) and/or memory addresses specifically for ISA adapters. This prevents PCI cards from trying to use the same settings ISA cards are using.
Page 122 BIOS Messages Message Description nnnn Cache SRAM Passed Where nnnn is the amount of system cache in kilobytes successfully tested. Diskette drive A error Diskette Drive is present but fails the BIOS POST diskette tests. Check to see that the drive is defined Diskette drive B error with the proper diskette type in Setup and that the diskette drive is correctly attached.
Page 123 BIOS Messages (Continued) Message Description Parity Check 1 nnnn* A parity error was found in the system bus (Parity Check 1) or the I/O bus (Parity Check 2). BIOS attempts to Parity Check 2 nnnn* locate and display the address on the screen. If it cannot locate the address, it displays.
Page 124: Post Error Codes And Messages
BIOS Messages (Continued) Message Description System timer error* The timer test failed. Requires repair of the system board. UMB upper limit segment address: nnnn Displays the address nnnn of the upper limit of the Upper Memory Blocks, indicating released segments of the BIOS which may be reclaimed by a virtual memory manager.
Page 125 POST Error Codes and Messages (Continued) Code Error Message 02B3 Incorrect Drive B type - run SETUP 02D0 System cache error - Cache disabled 02F5 DMA Test Failed 02F6 Software NMI Failed 0401 Invalid System Configuration Data - run configuration utility None System Configuration Data Read Error 0403...
Page 126 POST Error Codes and Messages (Continued) Code Error Message 810F Processor 2 failed FRB level 3 timer 8110 Server Management Interface failed to function 8120 IOP subsystem is not functional 8150 NVRAM Cleared by Jumper 8151 NVRAM Checksum Error, NVRAM cleared 8152 NVRAM Data Invalid, NVRAM cleared Sdfsdfsfdsdfsfdsdfsfd...
Page 127: System Cabling
System Cabling Before You Begin Static Precautions Standard Configuration RAID Configuration...
Page 128: Before You Begin
This appendix contains information and procedures on cabling configurations used in your system. The configurations include: Standard Configuration RAID Configuration. Before You Begin WARNING The DC push-button on/off switch on the front panel does not turn off the system AC power. Also, +5vdc is present on the system board whenever the AC power cord is connected between the system and an AC outlet.
Page 129: Standard Configuration
Standard Configuration Your system is cabled using a dual channel on-board IDE Controller and dual on-board Symbios Logic SYM53C875 SCSI Controllers. The on-board IDE controller supports the internally mounted CD-ROM as its first (master) device and an optional internally mounted IDE tape drive as its second (slave) device.
Page 130 Standard System Cable Configuration A— SCSI terminator B— SCSI Hard Disk Drives C— Wide SCSI interface cable D— Wide SCSI connector (68 pin) E— Diskette drive connector F— Diskette drive G— Diskette interface cable H— Primary IDE connector I— IDE Interface Cable J—...
Page 131 IDE CABLE (40-pins) WIDE SCSI CABLE (68-pins) OPTIONAL NARROW SCSI CABLE (50-pins Standard System Cable Routing System Cabling A-5...
Page 132: Raid Configuration
RAID Configuration One of the options available for your system is the RAID Controller board, which gives your system the added security of fault tolerance. If you order a system with the RAID controller, the system is pre-cabled at the factory. SecuRAID 100 (AMI MegaRAID E 762) RAID Controller XPRESS...
Page 133 Mylex AcceleRAID System Cable Configuration A— SCSI terminator B— SCSI Hard Disk Drives C— Wide SCSI interface cable D— Wide SCSI connector (68 pin) E— Diskette drive connector F— Diskette drive G— Diskette interface cable H— Primary IDE connector I— IDE Interface Cable J—...
Page 134 IDE CABLE (40-pins) WIDE SCSI CABLE (68-pins) OPTIONAL NARROW SCSI CABLE (50-pins) Mylex AcceleRAID System Cable Routing A-8 System Cabling...
Page 135: System Setup Utility
System Setup Utility System Setup Utility (SSU) Creating SSU Diskettes Running the SSU Exiting the SSU...
Page 136: System Setup Utility (Ssu
System Setup Utility (SSU) The System Setup Utility (SSU) is a DOS-based utility that supports extended system configuration operations for onboard resources and add-in boards. It also allows you to view the system event log and to set system boot and security options. Use the SSU when you need to: Add and remove ISA Legacy boards affecting the assignment of resources (ports, memory, IRQs, DMA) Change the server configuration resource settings...
Page 137: Creating Ssu Diskettes
Creating SSU Diskettes SSU may be run directly from the E CD-ROM or from XPRESS UILDER DOS-bootable diskettes. Before you can run the SSU from diskettes, you must copy the SSU from the E CD-ROM to a XPRESS UILDER diskette. If your diskette drive is disabled, or improperly configured, you must use the FLASH-resident BIOS Setup Utility (F2) to enable it so that you can use the SSU.
Page 138: Running The Ssu
Running the SSU 1. Turn on your video monitor and your system. 2. There are two ways to start the SSU: After creating an SSU diskette from the CD: Insert the SSU diskette in drive A, and reboot your server from the diskette. From diskette after installing your operating system: Insert the SSU diskette in Drive A.
Page 139: Customizing The Ssu
Customizing the SSU The SSU lets you customize the user interface according to your preferences. The AF sets these preferences and saves them in the AF.INI file so that they take effect the next time you start the SSU. There are three user-customizable settings: Color—this button lets you change the default colors associated with different items on the screen with predefined color combinations.
Page 140: Launching A Task
Launching a Task It is possible to have many tasks open at the same time, although some tasks may require complete control to avoid possible conflicts. The tasks achieve complete control by keeping the task as the center of operation until the user closes the task window. There are three ways to launch a task: In the SSU Main window, double-click on the task name under Available Tasks to display the main window for the selected task.
Page 141: Resource Configuration Add-In (Rca) Window
Resource Configuration Add-in (RCA) Window The RCA provides three major functions: Creates representations of devices that cannot be discovered by the system (ISA cards) Modifies the contents of the system by adding and removing devices Modifies the resources used by devices. You can use the RCA window to define an ISA card or add an ISA card by clicking on the appropriate button.
Page 142: Defining An Isa Card
RCA Window Defining an ISA Card An ISA card usually comes with a vendor-created .CFG file that specifies the resources the card requires to function properly. If the .CFG file is unavailable, you must manually create it or define the card through the SSU.
Page 143: Adding And Removing Isa Cards
Adding and Removing ISA Cards Adding and removing cards through the RCA provides a way for the RCA to run its conflict detection algorithms on the resources requested by the cards. This alerts you to any possible problems with that particular card in the current configuration.
Page 144: Modifying Resources
Modifying Resources Modifying the resources of a device may be necessary to accommodate certain operating systems, applications, and drivers. It may also be necessary to modify resources to resolve a conflict. To modify the resources associated with a device: 1. Highlight the device in the Devices section of the RCA window. 2.
Page 145: Recommended Resource Settings
Recommended Resource Settings The following table shows the recommended RCA system board settings for a sample system and provides a place for you to record any changes you make to the settings. Your System Group Normal Setting Configuration System Identification and Version Information SSU Configuration File Version Display Only...
Page 146: System Resource Usage
System Resource Usage Clicking on the Resource Use button in the Configuration window displays the System Resource Usage window. This window shows what resources each device is consuming. This information is useful for choosing resources if a conflict occurs. Devices can be organized according to the resources the user wants to examine using the options in the Resource section of the screen.
Page 147: Multiboot Add-In (Mba) Window
Multiboot Add-in (MBA) Window The MBA lets you set the system boot priority. The boot priority is the order the BIOS uses to boot the operating system from various devices in your system. To set the boot priority of your system: 1.
Page 148: System Event Log (Sel) Window
System Event Log (SEL) Window The SEL displays information on the events stored in the system log area. The information stored includes the name of the event, the date and time the event occurred and data pertinent to the event. Event data may include POST error codes that reflect hardware errors or software conflicts within the system.
Page 149: Exiting The Ssu
Exiting the SSU Exiting the SSU causes all windows to close. 1. Exit the SSU by opening the menu bar item File in the SSU Main window. 2. Click on Exit or Highlight Exit, and press Enter. System Setup Utility B-15...
Page 151: Emergency Management Port
Emergency Management Port Emergency Management Port How the EMP Works EMP Requirements and Configurations Setting Up the Server for the EMP Main EMP Window Phonebook Management Plug-ins...
Page 152: Emergency Management Port
Emergency Management Port The Emergency Management Port (EMP) allows remote server management via a modem or direct connection. The COM2 port on your server provides an interface to Console Manager software located in a second system. Modem Managed Server Management Console Sensors Event Console...
Page 153: How The Emp Works
How the EMP Works The EMP shares use of the COM 2 port with your system. When the EMP has control of the port, the port operates in command state. When the system has control of it, the port operates in redirect state.
Page 154 Console in Redirect State The above figure shows the EMP window in redirect state with the terminal window. The text that appears on the server monitor displays in the redirect window. Availability of the various EMP features is determined by two things: the EMP access mode selected during configuration in the System Management Submenu of the BIOS Server Menu, and if the server's COM 2 port is configured for console redirect in...
Page 155: Emp Requirements And Configurations
EMP Access Modes (Server not Configured for Console Redirect) Mode Server is powered off During POST After OS boots Disabled Redirect window Redirect window Redirect window appears, but is blank appears, but is appears, but is blank blank Pre-boot EMP commands EMP commands Redirect window available...
Page 156: Setting Up The Server For The Emp
For modem support, the server must use a Hayes compatible 14400 bps modem. The modem must be on the NT Hardware Compatibility List provided by Microsoft. The server modem must be set in auto-answer mode for the EMP to be able to connect to Setting Up the Server for the EMP To use the EMP, you must configure the server's BIOS with specific settings.
Page 157: Console Redirection Submenu
Console Redirection Submenu These settings in the Console Redirection Submenu of the Server menu must be set exactly as noted to be able to use the EMP. COM Port Address: Select 2F8. This is the COM 2 port that must be used by the EMP. The IRQ# setting automatically populates with the correct number based on the COM Port Address choice.
Page 158: Status Bar
Status Bar The status bar displays at the bottom of the current window. It contains the following status information: SERVER NAME: the name of the server (stored in the Phonebook). LINE: the type of line connection. This would be either direct or modem.
Page 159: Server Control Operations
Server Control Operations Three server control operations are available from the menu or toolbar of the main EMP window, remote server connection, powering the server on and off, and resetting the server. The server console mode can also be switched between EMP active and BIOS redirect modes through post-power-up and reset options.
Page 160: Power On/Off
Serial Line - must be filled out when the line selection is set to Direct connect (Serial Line). Baud Rate - must be 19200 for EMP to connect properly. COM Port No. - set the COM Port number to which the null modem serial cable is connected.
Page 161: Reset
Reset Selecting Reset from the Action menu generates the Reset dialog so that you can remotely reset the server with post-reset options. Reset Dialog Options available in the dialog are: System Reset - resets the server with the selected post-reset options. This operation is not allowed if the server is configured in RESTRICTED mode for EMP operations.
Page 162: Phonebook
Phonebook The EMP provides a support plug-in known as the Phonebook. The Phonebook stores names and numbers of servers in a list that can be updated by adding, modifying or deleting entries. The Phonebook can be opened from the main menu and tool bars, or launched from the Connect dialog by clicking the Config button.
Page 163: Management Plug-Ins
Cancel - exits the dialog without any action taken. Help - displays dialog level help information. Management Plug-ins SEL Viewer The SEL viewer provides access to the System Event Log on the server and can display records in either hexadecimal or text (verbose) form.
Page 164: Sel Viewer Menu Options
SEL Viewer Menu Options The following menu options are found on the SEL viewer menu bar: File Open - you can view SEL data from a previously saved file if it was stored in binary format. Selecting the Open menu item allows you to specify a filename under which the data is found.
Page 165: Sensor Type Codes
Window - gives options for displaying currently open windows. Help - provides version information for the SEL viewer and provides help topics on the EMP. Sensor Type Codes The Sensor Type Code Table provides information regarding: The type of sensor generating the SEL entry The name of the sensor The microcontroller which initiated the SEL entry The warning or error which initiated the SEL entry.
Page 166 Sensor Type Codes (continued) Sensor Type and Number in Sensor Name Generator ID Verbose Voltage # 06 5V Standby Voltage # 07 Baseboard SCSI-A Term1 Voltage # 08 Baseboard SCSI-A Term2 Voltage # 09 Baseboard SCSI-A Term3 Voltage # 0A Baseboard –12V Voltage # 0B Baseboard SCSI-B Term1...
Page 167: Sdr Viewer
System Event Logging Format Table Sensor Type and Sensor Type and Event Description Event type Event Description Number in Number in hex in hex verbose System Event #EF 12 EF E7 01 -- -- System Boot Event System Boot Event …...
Page 168: Sdr Viewer Menu Options
SDR Viewer Menu Options The following menu options are found on the SDR viewer menu bar: File Close - closes the SDR viewer. Exit - exits the EMP. View Display all Records - displays all records from the SDR repository. SDR Type - displays the records of a particular SDR type.
Page 169: Fru Viewer Menu Options
FRU Viewer Menu Options The following menu options are found on the FRU viewer menu bar: File Close - closes the FRU viewer. Exit - exits the EMP. View Display all Records - displays all FRU data, which consists of chassis, board, and product information. FRU Info - displays the FRU summary information as returned by the server.
Page 171 Glossary (Alternating Current) The type of current available in wall outlets. All computers must convert alternating current to direct current to operate. See also DC. address A label, name, or number that identifies a location in computer memory. ASCII (American Standard Code for Information Interchange) A standard number assigned to each of the alphanumeric characters and keyboard control code keys to enable the transfer of information between different types of computers and peripherals.
Page 172 Derived from BInary digiT, a bit is the smallest unit of information a computer handles. See also byte. (Baseboard Management Controller) Contains all of the server management functions. One major function of the BMC is to monitor system management events and log their occurrence in the System Event Log (SEL).
Page 173 configuration The way in which a computer is set up to operate. Some configurable options include CPU speed, serial port designation, and memory allocation. coprocessor See math coprocessor. (Central Processing Unit) See microprocessor. (Cathode-Ray Tube) The type of video display used in monitors for desktop computers.
Page 174 EEPROM (Electrically Erasable Programmable Read-Only Memory) A type of memory device that stores password and configuration information. (Enhanced Graphics Adapter) A type of video display system that provides medium-resolution text and graphics on TTL monochrome, color, and enhanced color monitors. The Emergency Management Port (EMP) provides an interface to the Console Manager.
Page 175 format The process used to organize a hard or floppy disk into sectors so it can accept data. Formatting destroys all previous data on the disk. (Gigabyte) 1,073,741,824 bytes. See also byte. hard disk drive See disk drive. hardware The physical parts of your computer, including the keyboard, monitor, disk drives, cables, and circuit cards.
Page 176 (Kilobyte) 1,024 bytes. See also byte. (Local Area Network) A group of computers linked together within a limited area to exchange information. (Liquid Crystal Display) The type of video display used in portable computers. (Light-Emitting Diode) A small electronic device that glows when current flows through it.
Page 177 modem A device used to exchange information with other computers over telephone or data lines. module A circuit board that plugs into a dedicated connector on the system board in your computer. mouse A small input device that you guide on a flat surface to control the cursor movement and operation of the computer when using certain software programs.
Page 178 Pentium A type of microprocessor, with a built-in math coprocessor, cache memory, and memory and bus controllers, that processes and communicates 32 bits of data at a time. This microprocessor also contains power management capabilities. peripheral A device connected to and controlled by the computer, such as an external disk drive or a printer.
Page 179 SCSI (Small Computer System Interface) An industry standard interface that provides high-speed access to tape drives, hard disk drives, and other peripheral devices. (System Event Log) A record of system management events. The information stored includes the name of the event, the date and time the event occurred and data pertinent to the event.
Page 180 tape drive A type of storage device using magnetic tape. (Transistor-Transistor Logic) A type of integrated circuit used in computers. See also CMOS. (Video Graphics Array) A type of video display system that provides high- resolution text and graphics on analog color monitors. 10 Glossary...
Page 181 Equipment Log Use this equipment log form to record pertinent information about your system. You will need some of this information to run the System Setup Utility. Be sure to update the equipment log when you add options. Record the model and serial numbers of the system components, dates of component removal or replacement, and the name of the vendor from whom the component was purchased.
Page 182 Serial Number Date Component Manufacturer Name & Model (if available) Installed Server System Board Processor 1 Processor 2 DIMM Slot 1 DIMM Slot 2 DIMM Slot 3 DIMM Slot 4 Modem Diskette Drive A Diskette Drive B Tape Drive 1 Tape Drive 2 CD-ROM Drive 1 Hard Disk Drive 1...
Page 183 Index EMP. See Emergency Management Port Console Add-in board Exit menu, configuring, Setup, 3-19 IDE bus slots, 1-8 ISA slots, 1-8 Add-in boards Hard Drive menu ISA, B-2 configuring, Setup, 3-18 PCI, B-2 Administrative password, 1-12 I2C bus for monitoring status, 1-11 Advanced Menu, configuring in Setup, 3-9 feature summary, 1-8...
Page 184 PCI Device, Slot 1 - Slot 7 menu, System board configuring in Setup, 3-10 boot block protect, jumper, 3-30 Power supply chassis intrusion detection, jumper, monitoring power state, 1-11 3-31 Problems configuration jumpers, 3-27 bootable CD-ROM not detected, System Chassis, 1-4 5-16 System setup utility CD-ROM drive activity light, 5-13...
Page 186 904475-04...

NEC LS2400 User Manual

Quick Links

Troubleshooting

Related Manuals for NEC LS2400

Summary of Contents for NEC LS2400

Table of Contents