Page 1 Programs After Market Services (PAMS) Technical Documentation SERVICE MANUAL [Issue 3: NMP Part No.0275426 ] [Issue 4: NMP Part No.0275571] NSM–3/3D SERIES CELLULAR PHONES NSM–3 issue 4: 02/2002 Copyright 2000, 2002. Nokia Corporation. All Rights Reserved.
Page 2: Amendment Record Sheet
Parts List for NSM–3 layouts 19 and 21 added, NSM 3D layout 05 added, HW list added. Schematic Diagrams for NSM–3 layout 19, 20, 21 added Schematic Diagrams for NSM–3D layout 05 added. Document repaginated. E 2002. Nokia Corporation. Issue 4 02/2002 Page 2...
Page 3 Removed from Service SW section. 28 pages. Service Tools pp 1 to 3, p.11, p.25, p.27 edited. p.13 JBA–6 replaced by BBF–1 p.14 ADS–3 removed p.26 Modular Cable Jack removed p.28 FLS–4s updated. E Nokia Mobile Phones Ltd. Issue 4 02/2002 Page 3...
Page 4 1. Foreword 2. General Information 3. System Module 4. UI Module 5. Product Variants NSM–3NX NSM–3DX 6. Service Software Instructions 6. Tuning Instructions 8. Service Tools 9. Disassembly/Troubleshooting Instructions 10. Non–serviceable Accessories E 2002. Nokia Corporation. Issue 4 02/2002 Page 4...
Page 5 While every endeavour has been made to ensure the accuracy of this document, some errors may exist. If any errors are found by the reader, NOKIA MOBILE PHONES Ltd should be notified in writing. Please state:...
Page 6: Warnings And Cautions
Ensure all cables and wires are repositioned correctly. All PC’s used with NMP Service Software for this produce must be bios and operating system ”Year 2000 Compliant”. E 2002. Nokia Corporation. Issue 4 02/2002 Page 6...
Page 7: General Information
PAMS Technical Documentation NSM–3/3D Series Transceivers General Information E Nokia Mobile Phones Ltd. Issue 3 11/2000...
Page 8: Table Of Contents
....... . . General Specifications of Transceiver NSM–3/3D ..E Nokia Mobile Phones Ltd. Page 2 Issue 3 11/2000...
Page 9: Product Selection
UK plug 90–264 Vac Performance Travel Charger ACP–8U 0675196 US plug 90–264 Vac Performance Travel Charger ACP–8C 0675211 China plug 90–264 Vac 10. Performance Travel Charger ACP–8A 0675214 Australia plug 90–264 Vac E Nokia Mobile Phones Ltd. Page 3 Issue 3 11/2000...
Page 10: Desktop Option
UK plug 90–264 Vac Performance Travel Charger ACP–8U 0675196 US plug 90–264 Vac Performance Travel Charger ACP–8C 0675211 China plug 90–264 Vac 10. Performance Travel Charger ACP–8A 0675214 Australia plug 90–264 Vac E Nokia Mobile Phones Ltd. Page 4 Issue 3 11/2000...
Page 11: Product And Module List
0720218 Swivel Mount HHS–12 0620054 Desk Stand DCV–1B 0675220 HF Microphone HFM–8 0690016 Plug&Play HF Cigarette Lighter Charger PPH–1 0675182 Cigarette Lighter Charger LCH–8 0675231 Cigarette Lighter Charger LCH–9 0675120 E Nokia Mobile Phones Ltd. Page 5 Issue 3 11/2000...
Page 12: Technical Specifications
Sensitivity, static channel GSM900: –102 dBm GSM1800: –100 dBm Frequency error, static channel < 0.1 ppm RMS phase error < 5.0 Peak phase error < 20.0 *) applies also to EGSM E Nokia Mobile Phones Ltd. Page 6 Issue 3 11/2000...
Page 13 PAMS Technical Documentation NSM–3/3D Series Transceivers General Information E Nokia Mobile Phones Ltd. Issue 3 11/2000...
Page 14 ....... . . General Specifications of Transceiver NSM–3/3D ..E Nokia Mobile Phones Ltd. Page 2 Issue 3 11/2000...
Page 15: Product Selection
UK plug 90–264 Vac Performance Travel Charger ACP–8U 0675196 US plug 90–264 Vac Performance Travel Charger ACP–8C 0675211 China plug 90–264 Vac 10. Performance Travel Charger ACP–8A 0675214 Australia plug 90–264 Vac E Nokia Mobile Phones Ltd. Page 3 Issue 3 11/2000...
Page 16: Desktop Option
UK plug 90–264 Vac Performance Travel Charger ACP–8U 0675196 US plug 90–264 Vac Performance Travel Charger ACP–8C 0675211 China plug 90–264 Vac 10. Performance Travel Charger ACP–8A 0675214 Australia plug 90–264 Vac E Nokia Mobile Phones Ltd. Page 4 Issue 3 11/2000...
Page 17: Product And Module List
0720218 Swivel Mount HHS–12 0620054 Desk Stand DCV–1B 0675220 HF Microphone HFM–8 0690016 Plug&Play HF Cigarette Lighter Charger PPH–1 0675182 Cigarette Lighter Charger LCH–8 0675231 Cigarette Lighter Charger LCH–9 0675120 E Nokia Mobile Phones Ltd. Page 5 Issue 3 11/2000...
Page 18: Technical Specifications
Sensitivity, static channel GSM900: –102 dBm GSM1800: –100 dBm Frequency error, static channel < 0.1 ppm RMS phase error < 5.0 Peak phase error < 20.0 *) applies also to EGSM E Nokia Mobile Phones Ltd. Page 6 Issue 3 11/2000...
Page 19 NSM–3 PAMS Technical Documentation System Module RM7L Connection between RF and Baseband modules (Version 1110 Edit 16) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–1...
Page 20 NSM–3 PAMS Technical Documentation System Module RM7L Baseband Block Interconnections (Version 1110 Edit 11) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–2...
Page 21 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of Power Supply (Version 1110 Edit 17) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–3...
Page 22 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of CPU Block (Version 1110 Edit 12) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–4...
Page 23 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of RF Block (Version 1110 Edit 28) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–5...
Page 24 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of Audio and RFI (Version 1110 Edit 15) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–6...
Page 25 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of IR Module (Version 1110 Edit 10) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–7...
Page 26 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of UI (Version 1110 Edit 412) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–8...
Page 27 NSM–3 PAMS Technical Documentation System Module RM7L Layout Diagram of RM7L – Top (Version 11) Layout Diagram of RM7L – Bottom (Version 11) E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–9...
Page 28 NSM–3 PAMS Technical Documentation System Module RM7L Testpoints of RM7L – Top (Version 0x) Testpoints of RM7L – Bottom (Version 11) E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–10...
Page 29 NSM–3 PAMS Technical Documentation System Module RM7L Connection between RF and Baseband modules (Version 1110 Edit 16) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–1...
Page 30 NSM–3 PAMS Technical Documentation System Module RM7L Baseband Block Interconnections (Version 1110 Edit 11) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–2...
Page 31 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of Power Supply (Version 1110 Edit 17) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–3...
Page 32 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of CPU Block (Version 1110 Edit 12) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–4...
Page 33 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of RF Block (Version 1110 Edit 28) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–5...
Page 34 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of Audio and RFI (Version 1110 Edit 15) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–6...
Page 35 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of IR Module (Version 1110 Edit 10) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–7...
Page 36 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of UI (Version 1110 Edit 412) for layout version 11 E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–8...
Page 37 NSM–3 PAMS Technical Documentation System Module RM7L Layout Diagram of RM7L – Top (Version 11) Layout Diagram of RM7L – Bottom (Version 11) E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–9...
Page 38 NSM–3 PAMS Technical Documentation System Module RM7L Testpoints of RM7L – Top (Version 0x) Testpoints of RM7L – Bottom (Version 11) E Nokia Mobile Phones Ltd. Issue 1 12/1999 A–10...
Page 39 NSM–3 PAMS Technical Documentation System Module RM7L Layout Diagram of RM7L – Top (Version 18) Layout Diagram of RM7L – Bottom (Version 18) E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–21...
Page 40 NSM–3 PAMS Technical Documentation System Module RM7L Testpoints of RM7L – Top (Version xx) Testpoints of RM7L – Bottom (Version 18) E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–22...
Page 41 NSM–3 PAMS Technical Documentation System Module RM7L Connection between RF and Baseband modules (HW 1910 Edit 4) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–23...
Page 42 NSM–3 PAMS Technical Documentation System Module RM7L Baseband Block Interconnections (HW 1910 Edit 4) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–24...
Page 43 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of Power Supply (HW 1510 Edit 4) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–25...
Page 44 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of CPU Block (HW 1910 Edit 5) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–26...
Page 45 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of RF Block (HW 1910 Edit 4) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–27...
Page 46 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of Audio and RFI (HW 1910 Edit 4) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–28...
Page 47 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of IR Module (HW 1910 Edit 4) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–29...
Page 48 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of UI (HW 1910 Edit 4) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–30...
Page 49 NSM–3 PAMS Technical Documentation System Module RM7L Layout Diagram of RM7L – Top (Version 19) Layout Diagram of RM7L – Bottom (Version 19) E Nokia Corporation. Issue 4 02/2002 A–31...
Page 50 NSM–3 PAMS Technical Documentation System Module RM7L Testpoints of RM7L – Bottom (Version 19) E Nokia Corporation. Issue 4 02/2002 A–32...
Page 51 NSM–3 PAMS Technical Documentation System Module RM7L Connection between RF and Baseband modules (HW 1910 Edit 4) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–23...
Page 52 NSM–3 PAMS Technical Documentation System Module RM7L Baseband Block Interconnections (HW 1910 Edit 4) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–24...
Page 53 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of Power Supply (HW 1510 Edit 4) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–25...
Page 54 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of CPU Block (HW 1910 Edit 5) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–26...
Page 55 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of RF Block (HW 1910 Edit 4) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–27...
Page 56 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of Audio and RFI (HW 1910 Edit 4) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–28...
Page 57 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of IR Module (HW 1910 Edit 4) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–29...
Page 58 NSM–3 PAMS Technical Documentation System Module RM7L Circuit Diagram of UI (HW 1910 Edit 4) for layout version 19 E Nokia Corporation. Issue 4 02/2002 A–30...
Page 59 NSM–3 PAMS Technical Documentation System Module RM7L Layout Diagram of RM7L – Top (Version 19) Layout Diagram of RM7L – Bottom (Version 19) E Nokia Corporation. Issue 4 02/2002 A–31...
Page 60 NSM–3 PAMS Technical Documentation System Module RM7L Testpoints of RM7L – Bottom (Version 19) E Nokia Corporation. Issue 4 02/2002 A–32...
Page 61 NSM–3D PAMS Technical Documentation System Module RM7LD Connection between RF and Baseband modules (Version 1410 Edit 4) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D1...
Page 62 NSM–3D PAMS Technical Documentation System Module RM7LD Baseband Block Interconnections (Version 1410 Edit 4) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D2...
Page 63 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of Power Supply (Version 1510 Edit 7) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D3...
Page 64 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of CPU Block (Version 1410 Edit 4) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D4...
Page 65 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of RF Block (Version 1410 Edit 3) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D5...
Page 66 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of Audio and RFI (Version 1410 Edit 3) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D6...
Page 67 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of IR Module (Version 1410 Edit 2) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D7...
Page 68 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of UI (Version 1410 Edit 4) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D8...
Page 69 NSM–3D PAMS Technical Documentation System Module RM7LD Layout Diagram of RM7LD – Top (Version 03) Layout Diagram of RM7LD – Bottom (Version 03) E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D9...
Page 70 NSM–3D PAMS Technical Documentation System Module RM7LD Testpoints of RM7LD – Top (Version 0x) Testpoints of RM7LD – Bottom (Version 03) E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D10...
Page 71 NSM–3D PAMS Technical Documentation System Module RM7LD Connection between RF and Baseband modules (Version 1410 Edit 4) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D1...
Page 72 NSM–3D PAMS Technical Documentation System Module RM7LD Baseband Block Interconnections (Version 1410 Edit 4) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D2...
Page 73 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of Power Supply (Version 1510 Edit 7) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D3...
Page 74 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of CPU Block (Version 1410 Edit 4) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D4...
Page 75 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of RF Block (Version 1410 Edit 3) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D5...
Page 76 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of Audio and RFI (Version 1410 Edit 3) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D6...
Page 77 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of IR Module (Version 1410 Edit 2) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D7...
Page 78 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of UI (Version 1410 Edit 4) for layout version 03 E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D8...
Page 79 NSM–3D PAMS Technical Documentation System Module RM7LD Layout Diagram of RM7LD – Top (Version 03) Layout Diagram of RM7LD – Bottom (Version 03) E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D9...
Page 80 NSM–3D PAMS Technical Documentation System Module RM7LD Testpoints of RM7LD – Top (Version 0x) Testpoints of RM7LD – Bottom (Version 03) E Nokia Mobile Phones Ltd. Issue 3 11/2000 A–D10...
Page 81 NSM–3D PAMS Technical Documentation System Module RM7LD Connection between RF and Baseband modules (Version 5.02 Edit 8) for layout version 05 E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D11...
Page 82 NSM–3D PAMS Technical Documentation System Module RM7LD Baseband Block Interconnections (Version 5.02 Edit 7) for layout version 05 E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D12...
Page 83 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of Power Supply (Version 5.02 Edit 9) for layout version 05 E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D13...
Page 84 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of CPU Block (Version 5.02 Edit 8) for layout version 05 E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D14...
Page 85 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of RF Block (Version 5.02 Edit 14) for layout version 05 E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D15...
Page 86 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of Audio and RFI (Version 5.02 Edit 6) for layout version 05 E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D16...
Page 87 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of IR Module (Version 5.02 Edit 3) for layout version 05 E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D17...
Page 89 NSM–3D PAMS Technical Documentation System Module RM7LD Layout Diagram of RM7LD – Bottom (Version 05) Layout Diagram of RM7LD – Top (Version 05) E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D19...
Page 91 NSM–3D PAMS Technical Documentation System Module RM7LD Connection between RF and Baseband modules (Version 5.02 Edit 8) for layout version 05 E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D11...
Page 92 NSM–3D PAMS Technical Documentation System Module RM7LD Baseband Block Interconnections (Version 5.02 Edit 7) for layout version 05 E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D12...
Page 93 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of Power Supply (Version 5.02 Edit 9) for layout version 05 E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D13...
Page 94 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of CPU Block (Version 5.02 Edit 8) for layout version 05 E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D14...
Page 95 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of RF Block (Version 5.02 Edit 14) for layout version 05 E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D15...
Page 96 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of Audio and RFI (Version 5.02 Edit 6) for layout version 05 E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D16...
Page 97 NSM–3D PAMS Technical Documentation System Module RM7LD Circuit Diagram of IR Module (Version 5.02 Edit 3) for layout version 05 E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D17...
Page 99 NSM–3D PAMS Technical Documentation System Module RM7LD Layout Diagram of RM7LD – Bottom (Version 05) Layout Diagram of RM7LD – Top (Version 05) E Nokia Corporation. All rights reserved. Issue 4 02/2002 A–D19...
Page 101 PAMS Technical Documentation NSM–3/3D Series Transceivers Product Variants E Nokia Corporation Issue 4 02/2002...
Page 102 ....Assembly Parts of NSM–3DX ......E Nokia Corporation Page 2 Issue 4 02/2002...
Page 103: Transceiver Nsm-3Nx
The Service Manual is intended for use by qualified service personnel only. Modules Transceiver NSM–3NX Basic Red 0503139 system module RM7L 0201386 mechanics MNSM3 0261995 Transceiver NSM–3NX Basic APAC 0502688 system module RM7L 0201386 mechanics MNSM3 0262152 E Nokia Corporation Page 3 Issue 4 02/2002...
Page 104: Exploded View Of Transceiver Nsm-3Nx
NSM–3/3D PAMS Technical Documentation Product Variants Exploded View of Transceiver NSM–3NX E Nokia Corporation Page 4 Issue 4 02/2002...
Page 105: Assembly Parts Of Nsm-3Nx
Twin Rip DMD06257 I023 0660196 Antenna EGSM/PCN I024 9510545 Battery latch spring DMD05129 I025 9451601 Battery latch DMD05083 * Note: Added to the phone in case of Bottom Conector related service required. E Nokia Corporation Page 5 Issue 4 02/2002...
Page 106: Transceiver Nsm-3Dx
SIM card is accessed after removal of battery cover. NOTE: The Service Manual is intended for use by qualified service personnel only. Modules Transceiver NSM–3DX APAC 0504747 system module RM7LD 0201682 mechanics MNSM3 0262379 E Nokia Corporation Page 6 Issue 4 02/2002...
Page 107: Exploded View Of Transceiver Nsm-3Dx
NSM–3/3D PAMS Technical Documentation Product Variants Exploded View of Transceiver NSM–3DX E Nokia Corporation Page 7 Issue 4 02/2002...
Page 108: Assembly Parts Of Nsm-3Dx
I020 9460327 A–cover fixing left DMD05127 I021 9460328 A–cover fixing right DMD05128 I022 9660147 Twin Rip DMD06257 I023 0660196 Antenna EGSM/PCN I024 9510545 Battery latch spring DMD05129 I025 9451601 Battery latch DMD05083 E Nokia Corporation Page 8 Issue 4 02/2002...
Page 109: Service Software Instructions
PAMS Technical Documentation NSM–3/3D Series Transceivers Service Software Instructions E Nokia Mobile Phones Ltd. Issue 4 02/2002...
Page 110 ......... . . E Nokia Mobile Phones Ltd.
Page 111 ......Phone Information... command ....E Nokia Mobile Phones Ltd. Page 3 Issue 4 02/2002...
Page 112: Service Software
Selections can be done by using keyboard and/or mouse. There is always a status bar displayed at the bottom of the main window which contains information about current actions. E Nokia Mobile Phones Ltd. Page 4 Issue 4 02/2002...
Page 113: Service Software
Service software NSM–3 and 3D specific: Service SW diskette 3.5” for NSM–3 (3D) 0774080 Flash SW packages on CD for NSM–3 0775223 Flash SW packages on CD for NSM–3D 0775280 E Nokia Mobile Phones Ltd. Page 5 Issue 4 02/2002...
Page 114 NSM–3/3D PAMS Technical Documentation Service Software Instructions This page intentionally left blank. E Nokia Mobile Phones Ltd. Page 6 Issue 4 02/2002...
Page 115: Installation
(errors in printing are possible) please try printing without the PKD–1. If printing is OK without the PKD–1 please contact your dealer. We will offer you a new PKD–1 in exchange for your old one. E Nokia Mobile Phones Ltd. Page 7 Issue 4 02/2002...
Page 116: Installing The Service Software On Pc Hard Disk
WinTesla is installed on your hard disk. When installation is completed remove the WinTesla software disk from your floppy drive. Insert the Dongle driver diskette into your floppy drive. Select the floppy drive and: E Nokia Mobile Phones Ltd. Page 8 Issue 4 02/2002...
Page 117: Installation Of Nsm-3 And 3D Support Modules
Follow the instructions on the screen. For Windows 95 and NT: Open Microsoft Explorer, select Start –Programs– Explorer Select the floppy drive. Start installation, double–click the file. nsek13i.exe Follow the instructions on the screen. E Nokia Mobile Phones Ltd. Page 9 Issue 4 02/2002...
Page 118: Common Properties Of The User Interface
Application version static text (–) Contains the name and version of the application. Copyright notice static text (–) Copyright is informed as: “Nokia Mobile Phones (c) 1996. All Rights Reserved”. Login Box edit box (–) The user Login ID edit box, where the user enters his faultlog user name.
Page 119: Main Window
The status bar contains information about the menu selections and events. The left area of the status bar describes the actions of menu items as the user uses the arrow keys to navigate through menus. E Nokia Mobile Phones Ltd. Page 11 Issue 4 02/2002...
Page 120 The Num Lock key is latched down. SCRL The Scroll Lock key is latched down. Tool bar The tool bar is NOT defined and will not be implemented until specified by this document. E Nokia Mobile Phones Ltd. Page 12 Issue 4 02/2002...
Page 121: Menu Bar
OK button before the operation is performed. Product The Product menu contains at least the following menu items: Ctrl+R Open... Close Initialize Normal Mode Local Mode Shift+F5 Faultlog Activate Faultlog... F9 Edit Faultlog... Exit Alt+F4 E Nokia Mobile Phones Ltd. Page 13 Issue 4 02/2002...
Page 122: Configure
Energy Management Calibration... Testing The Testing menu contains at least the following sections: RF Controls... RSSI Reading ... Self Tests ADC Readings Audio User Interface IR Test Sleep ModeTest Vibra Test... E Nokia Mobile Phones Ltd. Page 14 Issue 4 02/2002...
Page 123: Software
SCM & User settings ... Restore User Defaults... Set UI/DEV Default Values ... Operators Settings... IWR Swap... Flash Phone... View The View menu contains at least the following sections: Quick/RF Info... Phone Information... E Nokia Mobile Phones Ltd. Page 15 Issue 4 02/2002...
Page 124: Phone Identity Window
This window will not contain any con- trols other than a scroll bar. Help The Help menu contains at least the following menu items: Index General Help Using Help About WinTesla About AS Locals E Nokia Mobile Phones Ltd. Page 16 Issue 4 02/2002...
Page 125: Mouse Cursors
Exit Active Application Microsoft Alt+H Help Microsoft Ctrl Hot Keys Description Defined Ctrl+N File – New Microsoft Ctrl+O File – Open Microsoft Ctrl+P File – Print Microsoft Ctrl+R Product – New E Nokia Mobile Phones Ltd. Page 17 Issue 4 02/2002...
Page 126: Shift Hot Keys
Alt+T,R RX Calibration Alt+T,X Tx Power Alt+T,Q Tx I/Q Alt+T,E Eanergy Management calibration Alt+E Testing Menu Alt+E,F RF Controls Alt+E,R RSSI Reading Alt+E,S Self Tests Alt+E,A ADC Readings Alt+E,U Audio E Nokia Mobile Phones Ltd. Page 18 Issue 4 02/2002...
Page 127 View Menu Alt+V,Q Quick/RF Info Alt+V,P Phone Identity Alt+H Help Menu Microsoft Alt+H,I Index Microsoft Alt+H,G General Help Microsoft Alt+H,U Using Help Microsoft Alt+H,A About WinTesla Alt+H,S About AS Locals E Nokia Mobile Phones Ltd. Page 19 Issue 4 02/2002...
Page 128: Help Functions
Opens context sensitive help as F1–key does. Query Message Box Confirmations and questions are asked in a query message box . A query dialog box is recognized by the ?–icon. E Nokia Mobile Phones Ltd. Page 20 Issue 4 02/2002...
Page 129: Error Message Box
The dialog box will also contain an OK button and a Help button. OK button (default key): Acknowledges displayed information and terminate current op- eration. The dialog box is closed after selection. Help button (Alt+H): Open context sensitive help as F1–key does. E Nokia Mobile Phones Ltd. Page 21 Issue 4 02/2002...
Page 130: Custom Dialog Boxes
Cancel operation. Does not send or store anything and closes the dialog box. A greyed Cancel button indicates that it is not possible to quit from this dialog box. Yes button (ALT+Y or Y): E Nokia Mobile Phones Ltd. Page 22 Issue 4 02/2002...
Page 131: Reporting Status
OK button. E Nokia Mobile Phones Ltd. Page 23 Issue 4 02/2002...
Page 132: Nsm-3 And 3D Features
If the user selects No, application tries next connection, if there is one. Initialise... command Activation Status Bar Text Alt, P, I Opens a submenu which contains the following options: E Nokia Mobile Phones Ltd. Page 24 Issue 4 02/2002...
Page 133: Normal Mode
Also if quick info view is open it will be updated to RF Information view. Band... command This menu selection is for dual band phones. Activation Status Bar Text Alt, P, B Opens a submenu which contains following options: E Nokia Mobile Phones Ltd. Page 25 Issue 4 02/2002...
Page 134: Gsm
Service Software Instructions Activation Status Bar Text Alt, P, B, G Set phone to GSM band. Activation Status Bar Text Alt, P, B, P Set phone to PCN (GSM1800) band. E Nokia Mobile Phones Ltd. Page 26 Issue 4 02/2002...
Page 135: Tuning
The value is shown in the three different format decimal, hexa- decimal and binary. All these controls display the same value and changing one causes changes to others too. Measure button: This button activates the measurement. E Nokia Mobile Phones Ltd. Page 27 Issue 4 02/2002...
Page 136 PAMS Technical Documentation Service Software Instructions Save button: This saves values to the phone. Close button: This button closes the dialog without saving anything. Help button: This button opens Help. E Nokia Mobile Phones Ltd. Page 28 Issue 4 02/2002...
Page 137: Rx Calibration
3. The user is requested to put signal generator to low input level (read from .INI file). 4. Measurement with low input level is executed 5. The RX Calibration dialog will be updated when previous steps are done. E Nokia Mobile Phones Ltd. Page 29 Issue 4 02/2002...
Page 138 NOTE: After GSM calibration the same tuning must be made for the PCN band also! To change the band go to Product Menu and select Band , PCN. E Nokia Mobile Phones Ltd. Page 30 Issue 4 02/2002...
Page 139: Rx Am Suppression
Last line shows RSSI value. Measure button: This button causes the measurement to be done. When se- lected following dialog is shown. E Nokia Mobile Phones Ltd. Page 31 Issue 4 02/2002...
Page 140 PCN band also! To change the band go to Prod- uct Menu and select Band , PCN. Close button: This button closes the dialog without saving anything. Help button: This button opens Help. E Nokia Mobile Phones Ltd. Page 32 Issue 4 02/2002...
Page 141: Tx Power
After this switch to PCN band and do the tuning to levels 0, 11 and 15. Then Calculate the other levels and save the values. GSM900 TX Power Tuning dialog: GSM1800 TX Power Tuning dialog: E Nokia Mobile Phones Ltd. Page 33 Issue 4 02/2002...
Page 142 When Base level calculation is checked, base level is calculated and new base level target to list box is updated. Base level calculation check box: If this box is checked the base level is calculated. E Nokia Mobile Phones Ltd. Page 34 Issue 4 02/2002...
Page 143 The last used tuning power is in use after exit. The next automatic selection is made when this tuning function is ended: Operation Mode = RX pulsed When dialog is closed original band is selected. E Nokia Mobile Phones Ltd. Page 35 Issue 4 02/2002...
Page 144: Tx I/Q
Tune TX Q DC Offset scroll bar (ALT+Q): The operation of this function is the same as one above, ex- cept with this selection the Q branch DC Offset is tuned. The E Nokia Mobile Phones Ltd. Page 36 Issue 4 02/2002...
Page 145 The next automatic selection is made when TX I / Q tuning function is en- ded: Operation Mode = RX pulsed Update RF Information window NOTE: Tuning needs to be done for GSM900 and GSM1800 bands sepa- rately. E Nokia Mobile Phones Ltd. Page 37 Issue 4 02/2002...
Page 146: Energy Management Calibration
Remember to connect SCB–3 cable between Service Box JBU–6! When external power is connected and the user selects Yes to continue, the application displays the Energy Management Calibration dialog box: Dialog mode: modal E Nokia Mobile Phones Ltd. Page 38 Issue 4 02/2002...
Page 147 Close button (ESC): Dialog is closed. Help button (ALT+H): Context sensitive help. After battery a/d tunings a voltage setting request is shown to the user (Set supply voltage to 8.0 V). E Nokia Mobile Phones Ltd. Page 39 Issue 4 02/2002...
Page 148: Testing
– RX continuous mode channel is activated RF Information window is updated The RX value is always given as default. Note! Function is activated immediately, Apply is not needed. TX radio button (ALT+T): E Nokia Mobile Phones Ltd. Page 40 Issue 4 02/2002...
Page 149 TX Power have value OFF and is disabled ( greyed ) when ac- tive unit is RX. When the TX power is tuned with test value (smallest value) the TX Power has value TEST . E Nokia Mobile Phones Ltd. Page 41 Issue 4 02/2002...
Page 150 Active Unit = RX Update RF Information window The next table shows the dialog’s properties on different situations: ACTIVE UNIT = TX: TX Data Type: Updated AGC values: Greyed Monitoring Channel: Greyed E Nokia Mobile Phones Ltd. Page 42 Issue 4 02/2002...
Page 151 OPERATION MODE = BURST: AGC values: Greyed Continuous Mode Channel: Greyed Channel: Updated Monitoring Channel: Updated OPERATION MODE = CONT: AGC values: Updated Continuous Mode Channel: Updated Channel: Greyed Monitoring Channel: Greyed E Nokia Mobile Phones Ltd. Page 43 Issue 4 02/2002...
Page 152: Rssi Reading
RSSI value is read continuously until the user presses ESC–key or Close button to cancel reading. RSSI Reading dialog includes following items: Close (ENTER) button: Closes the RSSI Reading dialog. Does not send anything to phone. Help button: Context sensitive help. E Nokia Mobile Phones Ltd. Page 44 Issue 4 02/2002...
Page 153: Self Tests
Note that power–off test have no values, because if test has been passed, power has been turned off. If power–off test fails a special error message window is shown. If no response is received to power off test E Nokia Mobile Phones Ltd. Page 45 Issue 4 02/2002...
Page 154 7 CCONT Interface....8 A/D Converter....9 SW Reset......A Power Off....... B Security Data....C EEPROM Tune Checksum.... D PPM Checksum....E MCU Download DSP....F DSP Alive....... G COBBA Serial....... E Nokia Mobile Phones Ltd. Page 46 Issue 4 02/2002...
Page 155 NSM–3/3D PAMS Technical Documentation Service Software Instructions H COBBA Parallel..... I EEPROM Sec Checksum....J PPM Validity....K Warranty State....L SW Version....E Nokia Mobile Phones Ltd. Page 47 Issue 4 02/2002...
Page 156: Adc Readings
Closes the ADC Readings dialog. Does not send anything to phone. Help button: Context sensitive help. A/D Readings: Following a/d readings are measured: Battery Voltage..: Battery Temperature..: Charge Voltage..: Charge Current..: Battery Type....: Accessory Detection..: Hook....: RSSI....: VCXO Temperature..: E Nokia Mobile Phones Ltd. Page 48 Issue 4 02/2002...
Page 157: Audio
Volume On radio button (ALT+V): Turns buzzer on. Volume Off radio button (ALT+O): Turns buzzer off. Level drop down list (ALT+L): Sets level of a buzzer. Allowed range 0...127 Frequency radio button (ALT+Q): E Nokia Mobile Phones Ltd. Page 49 Issue 4 02/2002...
Page 158 Turns audio loop off. On radio button (ALT+N): Turns audio loop on. When the dialog is closed, the Buzzer Volume is always switched off. Also internal audio loop is turned off. E Nokia Mobile Phones Ltd. Page 50 Issue 4 02/2002...
Page 159: User Interface
In test display 2 none of the indicators are displayed and the display is filled with inverse chessboard pattern. When the dialog is closed the phone LCD display is cleared. E Nokia Mobile Phones Ltd. Page 51 Issue 4 02/2002...
Page 160: Ir Test
Dialog mode: modal IR Test dialog includes following items: Result box: Result can be OK/FAILED Test (ENTER) button: Starts the IR Test. Close button: Closes the IR Test dialog. E Nokia Mobile Phones Ltd. Page 52 Issue 4 02/2002...
Page 161: Sleep Mode
Edit box where you can enter a value in ms. Test (ENTER) button: Starts Sleep mode Test. Close button: Closes the Sleep mode Test dialog. When the dialog box is closed also the Sleep mode test is stopped. E Nokia Mobile Phones Ltd. Page 53 Issue 4 02/2002...
Page 162 NSM–3/3D PAMS Technical Documentation Service Software Instructions This page intentionally left blank. E Nokia Mobile Phones Ltd. Page 54 Issue 4 02/2002...
Page 163: Vibra Test
Edit box where you can enter value from 0 to 255. Test (ENTER) button: Starts Vibra Test. Close button: Closes the Vibra Test dialog. When the dialog box is closed also the vibra test is stopped. E Nokia Mobile Phones Ltd. Page 55 Issue 4 02/2002...
Page 164: Software
List allows the user to set options to each setting listed in the Settings list box. Save(OK) button (ENTER) Selections are accepted and saved to EEPROM. Cancel button (ESC) Selections are ignored and control is returned back to main menu. E Nokia Mobile Phones Ltd. Page 56 Issue 4 02/2002...
Page 165: Start Up Self-Tests
Selections are accepted and saved to EEPROM. A power up routine is made to the phone. Cancel button (ESC) Selections are ignored and control is returned back to main menu. Selectable Start–Up self tests: PPM Validity A/D Converter E Nokia Mobile Phones Ltd. Page 57 Issue 4 02/2002...
Page 166: Set Factory Values
Sets the selected factory value to phone. Before setting soft- ware asks confirmation: Cancel button: Closes the Default Factory Values dialog. Available Settings: User Interface Short Code Memory All (UI, SCM and call counters) E Nokia Mobile Phones Ltd. Page 58 Issue 4 02/2002...
Page 167: Phone Identity
(Input values are compared with values read from phone) The function opens Phone Identity dialog. Dialog mode: modal Phone Identity dialog includes following items: E Nokia Mobile Phones Ltd. Page 59 Issue 4 02/2002...
Page 168 File and ME operations contains both SIM Lock and IMEI data. IMEI Programming Data edit box (ALT+I): IMEI programming data is read from file or entered by the user to this field. SIM Lock Programming Data edit box (ALT+D): E Nokia Mobile Phones Ltd. Page 60 Issue 4 02/2002...
Page 169 File is selected with File Save As dialog. Load File... button (ALT+L): Reads a file containing data needed to program selected data. File is selected with File Open dialog. E Nokia Mobile Phones Ltd. Page 61 Issue 4 02/2002...
Page 170: Warranty State
This button is enabled only when phone is Repair Date or War- ranty Date is changed. Cancel button (ESC): Closes the dialog box and does not save the warranty state to the phone. E Nokia Mobile Phones Ltd. Page 62 Issue 4 02/2002...
Page 171: Production Data Edit
The user can edit HW version. OK button (ENTER): Closes the dialog box and writes HW version to ME. Cancel button (ESC): Closes the dialog box and does not write HW version to ME. E Nokia Mobile Phones Ltd. Page 63 Issue 4 02/2002...
Page 172: Dealer
Shows name of file picture file loaded. This picture is not avail- able, if phone does not support WUG. Save File... button (ALT+S): The user can save user settings to file. Load File button (ALT+L): E Nokia Mobile Phones Ltd. Page 64 Issue 4 02/2002...
Page 173: Short Code Memory
PIN and/or wait for SIM to wake up. Function opens the following Edit SCM dialog: Dialog mode: modal Edit SCM dialog includes the following items: Loc static text: Displays current location. Name edit box (ALT+A): E Nokia Mobile Phones Ltd. Page 65 Issue 4 02/2002...
Page 174 Edit SCM is back in control. The waiting state can be bro- ken with Cancel (ESC) button. If writing to the ME is broken, only part of the SCM entries in the ME may be changed. E Nokia Mobile Phones Ltd. Page 66 Issue 4 02/2002...
Page 175: Scm & User Settings
ME or file to which data is saved from ME. If the user selects OK button, the name of selected file is copied to File Name edit field. Close button (ESC): Closes the dialog box. E Nokia Mobile Phones Ltd. Page 67 Issue 4 02/2002...
Page 176: Restore User Defaults
Restore Default User Settings dialog box includes following items: Default Settings static text: The user can check one or more check boxes to restore corre- sponding defaults from file to ME. Check boxes are disabled/ E Nokia Mobile Phones Ltd. Page 68 Issue 4 02/2002...
Page 177: Set Ui/Dev Default Values
Reset phone to UI and SCM factory settings After selection the application asks confirmation: “Are you sure you want to set UI/DEV to factory settings?”. If Yes is answered, default settings are resetted to the phone. E Nokia Mobile Phones Ltd. Page 69 Issue 4 02/2002...
Page 178: Operators Settings
Saves settings to phone and closes dialog. Reset button (ALT+R): Clears operator settings form phone and closes dialog. Cancel button (ESC): Closes the dialog box and do not save settings to phone. E Nokia Mobile Phones Ltd. Page 70 Issue 4 02/2002...
Page 179: Iwr Swap
Edit box where the original serial number is shown Swapped SN: edit box (ALT+S): Edit box where the swapped serial number is shown Club Nokia ID: edit box (ALT+C): Edit box where the Club Nokia ID is shown E Nokia Mobile Phones Ltd. Page 71 Issue 4 02/2002...
Page 180: Flash Phone
This directory will then contain product specific INI–file e.g. NSM– X.INI in which the different market areas and files are described. NOTE: This is a screen sample for NSM–3, actual information may differ. Dialog mode: modal E Nokia Mobile Phones Ltd. Page 72 Issue 4 02/2002...
Page 181 Flash Image edit field. Usually you should use Market Area list box to select Image file. PPM group: Edit field (read only): E Nokia Mobile Phones Ltd. Page 73 Issue 4 02/2002...
Page 182 Hexadecimal value defining high erase limit, value should be plain hexadecimal without any prefix. Field value is read from flash pack ini–file, from entry HighEraseLimit. Force Download check box (ALT+D): E Nokia Mobile Phones Ltd. Page 74 Issue 4 02/2002...
Page 183 Dialog mode: modal. Phone Type Selection dialog includes following items: Phone Type group: List box: The user can select phone type. OK button (ENTER): The user accepts selected phone type. E Nokia Mobile Phones Ltd. Page 75 Issue 4 02/2002...
Page 184 The user can select ROM version of phone. OK button (ENTER): The user accepts the selected ROM version. Cancel button (ESC): ROM version selection is cancelled and operation is aborted. E Nokia Mobile Phones Ltd. Page 76 Issue 4 02/2002...
Page 185: View
If the NSM–3 phone is in normal mode, the following Quick Info is shown: Dialog mode: modeless If the NSM–3D phone is in normal mode, this Quick Info is shown: E Nokia Mobile Phones Ltd. Page 77 Issue 4 02/2002...
Page 186 It is also updated when ever needed. Dialog mode: modeless Selections show what data is currently updated by PC. E Nokia Mobile Phones Ltd. Page 78 Issue 4 02/2002...
Page 187: Phone Information
Command opens the Phone Identity Information dialog, which shows identification information. The information is shown in a modeless dialog which may be left open during other operations. It is also updated when ever needed. NSM–3, Dialog mode: modeless E Nokia Mobile Phones Ltd. Page 79 Issue 4 02/2002...
Page 188 Operation Mode (Operation Mode=) TX Data Type (TX Data Type=) Continuous Mode Channel (Cont Mode Channel=) Channel (Channel=) Monitoring Channel 1 (MonitoringChannel=) AGC dB value (AGC=) AGC Absolute Value (AGCAbsolute=) Front End (FrontEnd=) E Nokia Mobile Phones Ltd. Page 80 Issue 4 02/2002...
Page 189 All selections and parameters which are not same as in the RF Controls menu. TX Power Tuning dialog ([TX Power Tuning]) TX power coefficients TX I/Q Tuning dialog ([TX I/Q Tuning]) TX I/Q E Nokia Mobile Phones Ltd. Page 81 Issue 4 02/2002...
Page 190 NSM–3/3D PAMS Technical Documentation Service Software Instructions This page intentionally left blank. E Nokia Mobile Phones Ltd. Page 82 Issue 4 02/2002...
Page 191 PAMS Technical Documentation NSM–3/3D Series Transceivers Service Software Instructions E Nokia Mobile Phones Ltd. Issue 4 02/2002...
Page 192 ......... . . E Nokia Mobile Phones Ltd.
Page 193 ......Phone Information... command ....E Nokia Mobile Phones Ltd. Page 3 Issue 4 02/2002...
Page 194: Service Software
Selections can be done by using keyboard and/or mouse. There is always a status bar displayed at the bottom of the main window which contains information about current actions. E Nokia Mobile Phones Ltd. Page 4 Issue 4 02/2002...
Page 195: Service Software
Service software NSM–3 and 3D specific: Service SW diskette 3.5” for NSM–3 (3D) 0774080 Flash SW packages on CD for NSM–3 0775223 Flash SW packages on CD for NSM–3D 0775280 E Nokia Mobile Phones Ltd. Page 5 Issue 4 02/2002...
Page 196 NSM–3/3D PAMS Technical Documentation Service Software Instructions This page intentionally left blank. E Nokia Mobile Phones Ltd. Page 6 Issue 4 02/2002...
Page 197: Installation
(errors in printing are possible) please try printing without the PKD–1. If printing is OK without the PKD–1 please contact your dealer. We will offer you a new PKD–1 in exchange for your old one. E Nokia Mobile Phones Ltd. Page 7 Issue 4 02/2002...
Page 198: Installing The Service Software On Pc Hard Disk
WinTesla is installed on your hard disk. When installation is completed remove the WinTesla software disk from your floppy drive. Insert the Dongle driver diskette into your floppy drive. Select the floppy drive and: E Nokia Mobile Phones Ltd. Page 8 Issue 4 02/2002...
Page 199: Installation Of Nsm-3 And 3D Support Modules
Follow the instructions on the screen. For Windows 95 and NT: Open Microsoft Explorer, select Start –Programs– Explorer Select the floppy drive. Start installation, double–click the file. nsek13i.exe Follow the instructions on the screen. E Nokia Mobile Phones Ltd. Page 9 Issue 4 02/2002...
Page 200: Common Properties Of The User Interface
Application version static text (–) Contains the name and version of the application. Copyright notice static text (–) Copyright is informed as: “Nokia Mobile Phones (c) 1996. All Rights Reserved”. Login Box edit box (–) The user Login ID edit box, where the user enters his faultlog user name.
Page 201: Main Window
The status bar contains information about the menu selections and events. The left area of the status bar describes the actions of menu items as the user uses the arrow keys to navigate through menus. E Nokia Mobile Phones Ltd. Page 11 Issue 4 02/2002...
Page 202 The Num Lock key is latched down. SCRL The Scroll Lock key is latched down. Tool bar The tool bar is NOT defined and will not be implemented until specified by this document. E Nokia Mobile Phones Ltd. Page 12 Issue 4 02/2002...
Page 203: Menu Bar
OK button before the operation is performed. Product The Product menu contains at least the following menu items: Ctrl+R Open... Close Initialize Normal Mode Local Mode Shift+F5 Faultlog Activate Faultlog... F9 Edit Faultlog... Exit Alt+F4 E Nokia Mobile Phones Ltd. Page 13 Issue 4 02/2002...
Page 204: Configure
Energy Management Calibration... Testing The Testing menu contains at least the following sections: RF Controls... RSSI Reading ... Self Tests ADC Readings Audio User Interface IR Test Sleep ModeTest Vibra Test... E Nokia Mobile Phones Ltd. Page 14 Issue 4 02/2002...
Page 205: Software
SCM & User settings ... Restore User Defaults... Set UI/DEV Default Values ... Operators Settings... IWR Swap... Flash Phone... View The View menu contains at least the following sections: Quick/RF Info... Phone Information... E Nokia Mobile Phones Ltd. Page 15 Issue 4 02/2002...
Page 206: Phone Identity Window
This window will not contain any con- trols other than a scroll bar. Help The Help menu contains at least the following menu items: Index General Help Using Help About WinTesla About AS Locals E Nokia Mobile Phones Ltd. Page 16 Issue 4 02/2002...
Page 207: Mouse Cursors
Exit Active Application Microsoft Alt+H Help Microsoft Ctrl Hot Keys Description Defined Ctrl+N File – New Microsoft Ctrl+O File – Open Microsoft Ctrl+P File – Print Microsoft Ctrl+R Product – New E Nokia Mobile Phones Ltd. Page 17 Issue 4 02/2002...
Page 208: Shift Hot Keys
Alt+T,R RX Calibration Alt+T,X Tx Power Alt+T,Q Tx I/Q Alt+T,E Eanergy Management calibration Alt+E Testing Menu Alt+E,F RF Controls Alt+E,R RSSI Reading Alt+E,S Self Tests Alt+E,A ADC Readings Alt+E,U Audio E Nokia Mobile Phones Ltd. Page 18 Issue 4 02/2002...
Page 209 View Menu Alt+V,Q Quick/RF Info Alt+V,P Phone Identity Alt+H Help Menu Microsoft Alt+H,I Index Microsoft Alt+H,G General Help Microsoft Alt+H,U Using Help Microsoft Alt+H,A About WinTesla Alt+H,S About AS Locals E Nokia Mobile Phones Ltd. Page 19 Issue 4 02/2002...
Page 210: Help Functions
Opens context sensitive help as F1–key does. Query Message Box Confirmations and questions are asked in a query message box . A query dialog box is recognized by the ?–icon. E Nokia Mobile Phones Ltd. Page 20 Issue 4 02/2002...
Page 211: Error Message Box
The dialog box will also contain an OK button and a Help button. OK button (default key): Acknowledges displayed information and terminate current op- eration. The dialog box is closed after selection. Help button (Alt+H): Open context sensitive help as F1–key does. E Nokia Mobile Phones Ltd. Page 21 Issue 4 02/2002...
Page 212: Custom Dialog Boxes
Cancel operation. Does not send or store anything and closes the dialog box. A greyed Cancel button indicates that it is not possible to quit from this dialog box. Yes button (ALT+Y or Y): E Nokia Mobile Phones Ltd. Page 22 Issue 4 02/2002...
Page 213: Reporting Status
OK button. E Nokia Mobile Phones Ltd. Page 23 Issue 4 02/2002...
Page 214: Nsm-3 And 3D Features
If the user selects No, application tries next connection, if there is one. Initialise... command Activation Status Bar Text Alt, P, I Opens a submenu which contains the following options: E Nokia Mobile Phones Ltd. Page 24 Issue 4 02/2002...
Page 215: Normal Mode
Also if quick info view is open it will be updated to RF Information view. Band... command This menu selection is for dual band phones. Activation Status Bar Text Alt, P, B Opens a submenu which contains following options: E Nokia Mobile Phones Ltd. Page 25 Issue 4 02/2002...
Page 216: Gsm
Service Software Instructions Activation Status Bar Text Alt, P, B, G Set phone to GSM band. Activation Status Bar Text Alt, P, B, P Set phone to PCN (GSM1800) band. E Nokia Mobile Phones Ltd. Page 26 Issue 4 02/2002...
Page 217: Tuning
The value is shown in the three different format decimal, hexa- decimal and binary. All these controls display the same value and changing one causes changes to others too. Measure button: This button activates the measurement. E Nokia Mobile Phones Ltd. Page 27 Issue 4 02/2002...
Page 218 PAMS Technical Documentation Service Software Instructions Save button: This saves values to the phone. Close button: This button closes the dialog without saving anything. Help button: This button opens Help. E Nokia Mobile Phones Ltd. Page 28 Issue 4 02/2002...
Page 219: Rx Calibration
3. The user is requested to put signal generator to low input level (read from .INI file). 4. Measurement with low input level is executed 5. The RX Calibration dialog will be updated when previous steps are done. E Nokia Mobile Phones Ltd. Page 29 Issue 4 02/2002...
Page 220 NOTE: After GSM calibration the same tuning must be made for the PCN band also! To change the band go to Product Menu and select Band , PCN. E Nokia Mobile Phones Ltd. Page 30 Issue 4 02/2002...
Page 221: Rx Am Suppression
Last line shows RSSI value. Measure button: This button causes the measurement to be done. When se- lected following dialog is shown. E Nokia Mobile Phones Ltd. Page 31 Issue 4 02/2002...
Page 222 PCN band also! To change the band go to Prod- uct Menu and select Band , PCN. Close button: This button closes the dialog without saving anything. Help button: This button opens Help. E Nokia Mobile Phones Ltd. Page 32 Issue 4 02/2002...
Page 223: Tx Power
After this switch to PCN band and do the tuning to levels 0, 11 and 15. Then Calculate the other levels and save the values. GSM900 TX Power Tuning dialog: GSM1800 TX Power Tuning dialog: E Nokia Mobile Phones Ltd. Page 33 Issue 4 02/2002...
Page 224 When Base level calculation is checked, base level is calculated and new base level target to list box is updated. Base level calculation check box: If this box is checked the base level is calculated. E Nokia Mobile Phones Ltd. Page 34 Issue 4 02/2002...
Page 225 The last used tuning power is in use after exit. The next automatic selection is made when this tuning function is ended: Operation Mode = RX pulsed When dialog is closed original band is selected. E Nokia Mobile Phones Ltd. Page 35 Issue 4 02/2002...
Page 226: Tx I/Q
Tune TX Q DC Offset scroll bar (ALT+Q): The operation of this function is the same as one above, ex- cept with this selection the Q branch DC Offset is tuned. The E Nokia Mobile Phones Ltd. Page 36 Issue 4 02/2002...
Page 227 The next automatic selection is made when TX I / Q tuning function is en- ded: Operation Mode = RX pulsed Update RF Information window NOTE: Tuning needs to be done for GSM900 and GSM1800 bands sepa- rately. E Nokia Mobile Phones Ltd. Page 37 Issue 4 02/2002...
Page 228: Energy Management Calibration
Remember to connect SCB–3 cable between Service Box JBU–6! When external power is connected and the user selects Yes to continue, the application displays the Energy Management Calibration dialog box: Dialog mode: modal E Nokia Mobile Phones Ltd. Page 38 Issue 4 02/2002...
Page 229 Close button (ESC): Dialog is closed. Help button (ALT+H): Context sensitive help. After battery a/d tunings a voltage setting request is shown to the user (Set supply voltage to 8.0 V). E Nokia Mobile Phones Ltd. Page 39 Issue 4 02/2002...
Page 230: Testing
– RX continuous mode channel is activated RF Information window is updated The RX value is always given as default. Note! Function is activated immediately, Apply is not needed. TX radio button (ALT+T): E Nokia Mobile Phones Ltd. Page 40 Issue 4 02/2002...
Page 231 TX Power have value OFF and is disabled ( greyed ) when ac- tive unit is RX. When the TX power is tuned with test value (smallest value) the TX Power has value TEST . E Nokia Mobile Phones Ltd. Page 41 Issue 4 02/2002...
Page 232 Active Unit = RX Update RF Information window The next table shows the dialog’s properties on different situations: ACTIVE UNIT = TX: TX Data Type: Updated AGC values: Greyed Monitoring Channel: Greyed E Nokia Mobile Phones Ltd. Page 42 Issue 4 02/2002...
Page 233 OPERATION MODE = BURST: AGC values: Greyed Continuous Mode Channel: Greyed Channel: Updated Monitoring Channel: Updated OPERATION MODE = CONT: AGC values: Updated Continuous Mode Channel: Updated Channel: Greyed Monitoring Channel: Greyed E Nokia Mobile Phones Ltd. Page 43 Issue 4 02/2002...
Page 234: Rssi Reading
RSSI value is read continuously until the user presses ESC–key or Close button to cancel reading. RSSI Reading dialog includes following items: Close (ENTER) button: Closes the RSSI Reading dialog. Does not send anything to phone. Help button: Context sensitive help. E Nokia Mobile Phones Ltd. Page 44 Issue 4 02/2002...
Page 235: Self Tests
Note that power–off test have no values, because if test has been passed, power has been turned off. If power–off test fails a special error message window is shown. If no response is received to power off test E Nokia Mobile Phones Ltd. Page 45 Issue 4 02/2002...
Page 236 7 CCONT Interface....8 A/D Converter....9 SW Reset......A Power Off....... B Security Data....C EEPROM Tune Checksum.... D PPM Checksum....E MCU Download DSP....F DSP Alive....... G COBBA Serial....... E Nokia Mobile Phones Ltd. Page 46 Issue 4 02/2002...
Page 237 NSM–3/3D PAMS Technical Documentation Service Software Instructions H COBBA Parallel..... I EEPROM Sec Checksum....J PPM Validity....K Warranty State....L SW Version....E Nokia Mobile Phones Ltd. Page 47 Issue 4 02/2002...
Page 238: Adc Readings
Closes the ADC Readings dialog. Does not send anything to phone. Help button: Context sensitive help. A/D Readings: Following a/d readings are measured: Battery Voltage..: Battery Temperature..: Charge Voltage..: Charge Current..: Battery Type....: Accessory Detection..: Hook....: RSSI....: VCXO Temperature..: E Nokia Mobile Phones Ltd. Page 48 Issue 4 02/2002...
Page 239: Audio
Volume On radio button (ALT+V): Turns buzzer on. Volume Off radio button (ALT+O): Turns buzzer off. Level drop down list (ALT+L): Sets level of a buzzer. Allowed range 0...127 Frequency radio button (ALT+Q): E Nokia Mobile Phones Ltd. Page 49 Issue 4 02/2002...
Page 240 Turns audio loop off. On radio button (ALT+N): Turns audio loop on. When the dialog is closed, the Buzzer Volume is always switched off. Also internal audio loop is turned off. E Nokia Mobile Phones Ltd. Page 50 Issue 4 02/2002...
Page 241: User Interface
In test display 2 none of the indicators are displayed and the display is filled with inverse chessboard pattern. When the dialog is closed the phone LCD display is cleared. E Nokia Mobile Phones Ltd. Page 51 Issue 4 02/2002...
Page 242: Ir Test
Dialog mode: modal IR Test dialog includes following items: Result box: Result can be OK/FAILED Test (ENTER) button: Starts the IR Test. Close button: Closes the IR Test dialog. E Nokia Mobile Phones Ltd. Page 52 Issue 4 02/2002...
Page 243: Sleep Mode
Edit box where you can enter a value in ms. Test (ENTER) button: Starts Sleep mode Test. Close button: Closes the Sleep mode Test dialog. When the dialog box is closed also the Sleep mode test is stopped. E Nokia Mobile Phones Ltd. Page 53 Issue 4 02/2002...
Page 244 NSM–3/3D PAMS Technical Documentation Service Software Instructions This page intentionally left blank. E Nokia Mobile Phones Ltd. Page 54 Issue 4 02/2002...
Page 245: Vibra Test
Edit box where you can enter value from 0 to 255. Test (ENTER) button: Starts Vibra Test. Close button: Closes the Vibra Test dialog. When the dialog box is closed also the vibra test is stopped. E Nokia Mobile Phones Ltd. Page 55 Issue 4 02/2002...
Page 246: Software
List allows the user to set options to each setting listed in the Settings list box. Save(OK) button (ENTER) Selections are accepted and saved to EEPROM. Cancel button (ESC) Selections are ignored and control is returned back to main menu. E Nokia Mobile Phones Ltd. Page 56 Issue 4 02/2002...
Page 247: Start Up Self-Tests
Selections are accepted and saved to EEPROM. A power up routine is made to the phone. Cancel button (ESC) Selections are ignored and control is returned back to main menu. Selectable Start–Up self tests: PPM Validity A/D Converter E Nokia Mobile Phones Ltd. Page 57 Issue 4 02/2002...
Page 248: Set Factory Values
Sets the selected factory value to phone. Before setting soft- ware asks confirmation: Cancel button: Closes the Default Factory Values dialog. Available Settings: User Interface Short Code Memory All (UI, SCM and call counters) E Nokia Mobile Phones Ltd. Page 58 Issue 4 02/2002...
Page 249: Phone Identity
(Input values are compared with values read from phone) The function opens Phone Identity dialog. Dialog mode: modal Phone Identity dialog includes following items: E Nokia Mobile Phones Ltd. Page 59 Issue 4 02/2002...
Page 250 File and ME operations contains both SIM Lock and IMEI data. IMEI Programming Data edit box (ALT+I): IMEI programming data is read from file or entered by the user to this field. SIM Lock Programming Data edit box (ALT+D): E Nokia Mobile Phones Ltd. Page 60 Issue 4 02/2002...
Page 251 File is selected with File Save As dialog. Load File... button (ALT+L): Reads a file containing data needed to program selected data. File is selected with File Open dialog. E Nokia Mobile Phones Ltd. Page 61 Issue 4 02/2002...
Page 252: Warranty State
This button is enabled only when phone is Repair Date or War- ranty Date is changed. Cancel button (ESC): Closes the dialog box and does not save the warranty state to the phone. E Nokia Mobile Phones Ltd. Page 62 Issue 4 02/2002...
Page 253: Production Data Edit
The user can edit HW version. OK button (ENTER): Closes the dialog box and writes HW version to ME. Cancel button (ESC): Closes the dialog box and does not write HW version to ME. E Nokia Mobile Phones Ltd. Page 63 Issue 4 02/2002...
Page 254: Dealer
Shows name of file picture file loaded. This picture is not avail- able, if phone does not support WUG. Save File... button (ALT+S): The user can save user settings to file. Load File button (ALT+L): E Nokia Mobile Phones Ltd. Page 64 Issue 4 02/2002...
Page 255: Short Code Memory
PIN and/or wait for SIM to wake up. Function opens the following Edit SCM dialog: Dialog mode: modal Edit SCM dialog includes the following items: Loc static text: Displays current location. Name edit box (ALT+A): E Nokia Mobile Phones Ltd. Page 65 Issue 4 02/2002...
Page 256 Edit SCM is back in control. The waiting state can be bro- ken with Cancel (ESC) button. If writing to the ME is broken, only part of the SCM entries in the ME may be changed. E Nokia Mobile Phones Ltd. Page 66 Issue 4 02/2002...
Page 257: Scm & User Settings
ME or file to which data is saved from ME. If the user selects OK button, the name of selected file is copied to File Name edit field. Close button (ESC): Closes the dialog box. E Nokia Mobile Phones Ltd. Page 67 Issue 4 02/2002...
Page 258: Restore User Defaults
Restore Default User Settings dialog box includes following items: Default Settings static text: The user can check one or more check boxes to restore corre- sponding defaults from file to ME. Check boxes are disabled/ E Nokia Mobile Phones Ltd. Page 68 Issue 4 02/2002...
Page 259: Set Ui/Dev Default Values
Reset phone to UI and SCM factory settings After selection the application asks confirmation: “Are you sure you want to set UI/DEV to factory settings?”. If Yes is answered, default settings are resetted to the phone. E Nokia Mobile Phones Ltd. Page 69 Issue 4 02/2002...
Page 260: Operators Settings
Saves settings to phone and closes dialog. Reset button (ALT+R): Clears operator settings form phone and closes dialog. Cancel button (ESC): Closes the dialog box and do not save settings to phone. E Nokia Mobile Phones Ltd. Page 70 Issue 4 02/2002...
Page 261: Iwr Swap
Edit box where the original serial number is shown Swapped SN: edit box (ALT+S): Edit box where the swapped serial number is shown Club Nokia ID: edit box (ALT+C): Edit box where the Club Nokia ID is shown E Nokia Mobile Phones Ltd. Page 71 Issue 4 02/2002...
Page 262: Flash Phone
This directory will then contain product specific INI–file e.g. NSM– X.INI in which the different market areas and files are described. NOTE: This is a screen sample for NSM–3, actual information may differ. Dialog mode: modal E Nokia Mobile Phones Ltd. Page 72 Issue 4 02/2002...
Page 263 Flash Image edit field. Usually you should use Market Area list box to select Image file. PPM group: Edit field (read only): E Nokia Mobile Phones Ltd. Page 73 Issue 4 02/2002...
Page 264 Hexadecimal value defining high erase limit, value should be plain hexadecimal without any prefix. Field value is read from flash pack ini–file, from entry HighEraseLimit. Force Download check box (ALT+D): E Nokia Mobile Phones Ltd. Page 74 Issue 4 02/2002...
Page 265 Dialog mode: modal. Phone Type Selection dialog includes following items: Phone Type group: List box: The user can select phone type. OK button (ENTER): The user accepts selected phone type. E Nokia Mobile Phones Ltd. Page 75 Issue 4 02/2002...
Page 266 The user can select ROM version of phone. OK button (ENTER): The user accepts the selected ROM version. Cancel button (ESC): ROM version selection is cancelled and operation is aborted. E Nokia Mobile Phones Ltd. Page 76 Issue 4 02/2002...
Page 267: View
If the NSM–3 phone is in normal mode, the following Quick Info is shown: Dialog mode: modeless If the NSM–3D phone is in normal mode, this Quick Info is shown: E Nokia Mobile Phones Ltd. Page 77 Issue 4 02/2002...
Page 268 It is also updated when ever needed. Dialog mode: modeless Selections show what data is currently updated by PC. E Nokia Mobile Phones Ltd. Page 78 Issue 4 02/2002...
Page 269: Phone Information
Command opens the Phone Identity Information dialog, which shows identification information. The information is shown in a modeless dialog which may be left open during other operations. It is also updated when ever needed. NSM–3, Dialog mode: modeless E Nokia Mobile Phones Ltd. Page 79 Issue 4 02/2002...
Page 270 Operation Mode (Operation Mode=) TX Data Type (TX Data Type=) Continuous Mode Channel (Cont Mode Channel=) Channel (Channel=) Monitoring Channel 1 (MonitoringChannel=) AGC dB value (AGC=) AGC Absolute Value (AGCAbsolute=) Front End (FrontEnd=) E Nokia Mobile Phones Ltd. Page 80 Issue 4 02/2002...
Page 271 All selections and parameters which are not same as in the RF Controls menu. TX Power Tuning dialog ([TX Power Tuning]) TX power coefficients TX I/Q Tuning dialog ([TX I/Q Tuning]) TX I/Q E Nokia Mobile Phones Ltd. Page 81 Issue 4 02/2002...
Page 272 NSM–3/3D PAMS Technical Documentation Service Software Instructions This page intentionally left blank. E Nokia Mobile Phones Ltd. Page 82 Issue 4 02/2002...
Page 273: Service Tools
PAMS Technical Documentation NSM–3/3D Series Transceivers Service Tools E Nokia Corporation. Issue 4 02/2002...
Page 274 ......... E Nokia Corporation.
Page 275 ..........E Nokia Corporation.
Page 276: Service Box Jbu-6
Product Code Service Box JBU-6: 0770153 View of JBU-6 SCD-6: Sales Package code: 0080329 Pinset Cable SCD-6: Spare part for JBU-6. RF Module RL6 for Service Box JBU-6 RF Module RL6: 0770172 E Nokia Corporation. Page 4 Issue 4 02/2002...
Page 277: Test Jig Mjs-9
See next page for additional info. Product Code Module Jig MJS-9: 0770154 View of MJS-9 *Note: The nominal supply voltage for MJS-9 is +8.0 V. The supply voltage must not exceed +15.0 V. (MJS-9 has overvoltage protection). E Nokia Corporation. Page 5 Issue 4 02/2002...
Page 278 Use LCD module CD9 when servicing with MJS-9. Product code: 0770244 Remove LCD/Keymat module from PCB before installing the radio module into the Service Jig MJS-9. Use LCD module CD9 0770244 instead of the original NSM-3 module. E Nokia Corporation. Page 6 Issue 4 02/2002...
Page 279: Soldering Jig Mjs-21
The Soldering Jig MJS-21 is used for soldering (in automatic soldering machines) and as a rework jig for system module, if special fixtures (like extra feet) are used. Product Code Module Jig MJS-21: 0770225 View of MJS-21 E Nokia Corporation. Page 7 Issue 4 02/2002...
Page 280: Flash Loading Adapter Fla-10
Sales package code Falsh Loading Adapter FLA-10: 0081346 Sales package contains: Falsh Loading Adapter FLA-10 (bulk) 0770229 DC Cable FLC-2 0730185 View of FLA-10 View of FLC-2 E Nokia Corporation. Page 8 Issue 4 02/2002...
Page 281: Battery Connector Extractor Tool Srt-3
Service Tools Battery Connector Extractor Tool SRT-3 The Battery Connector Extractor Tool is used to remove battery connector from the frame. Product Code Battery Connector Extractor Tool SRT-3: 0770226 View of SRT-3 E Nokia Corporation. Page 9 Issue 4 02/2002...
Page 282: Flash Loading Adapter Fla-7 (Sales Pack)
- Flash Loading Adapter FLA-7 0770119 - Service Cable XCM-5 0730142 - Power Cable SCF-7 0730141 - Service Cable assy AXS-5 0730091 Sales package code Flash Loading Adapter FLA-7: 0080326 View of FLA-7 E Nokia Corporation. Page 10 Issue 4 02/2002...
Page 283: Flash Prommer Fps-4S (Sales Pack)
AXS-4 cable D9-D9 0774043 Prommer software diskette Extension modules available : SF6 SRAM Extension module 0200742 SF7 FLASH Memory Extension module 0200743 Sales package code Flash Prommer FPS-4S: 0085095 View of FPS-4 E Nokia Corporation. Page 11 Issue 4 02/2002...
Page 284: Security Box Tdf-4
View of IR Data Interface Module JLP-1 IR Data Interface Module JLP-1 fits in the Security Box TDF-4 and can be used to perform IR tests with WinTesla. Product Code IR Data Interface Module JLP-1: 0750079 E Nokia Corporation. Page 12 Issue 4 02/2002...
Page 285: Product Code
1825019 Product Code Flash Battery BBF-1: 0775206 View of BBF-1 *Note: The nominal supply voltage for BBF-1 is +8.0 V. The supply voltage must not exceed +15.0 V. (BBF-1 has overvoltage protection). E Nokia Corporation. Page 13 Issue 4 02/2002...
Page 286 NSM–3/3D PAMS Technical Documentation Service Tools This page intentionally left blank. E Nokia Corporation. Page 14 Issue 4 02/2002...
Page 287: Service Cable Axs-4
The D9-D9 Service Cable AXS-4 is used to connect two 9 pin D connec- tors e.g. between PC and TDF-4 seurity box. Cable lenght is 2 meters. Product code D9-D9 Service Cable AXS-4 0730090 View of AXS-4 E Nokia Corporation. Page 15 Issue 4 02/2002...
Page 288: Service Cable Axs-4U
The D9-D9 Service Cable AXS-4U is used to connect two 9 pin D connec- tors e.g. between PC’s serial port and FLS-2D. Cable length is 30 cm. Product code D9-D9 Service Cable AXS-4U 0730163 View of AXS-4U E Nokia Corporation. Page 16 Issue 4 02/2002...
Page 289: D15-D15 Cable Axs-5
Service Tools D15-D15 Cable AXS-5 The D15-D15 Cable AXS-5 is used to connect two 15 pin D connectors. e.g. between FLA-5/7 and FPS-4S. Product Code D15-D15 Cable AXS-5: 0730091 View of AXS-5 E Nokia Corporation. Page 17 Issue 4 02/2002...
Page 290: Mbus Cable Dau-9S
MBUS Cable DAU-9S The MBUS Cable DAU-9S has a modular connector, and is used with be- tween PC’s serial port and eg. Service Box JBU-6. Product Code MBUS Cable DAU-9S: 0730108 View of DAU-9S E Nokia Corporation. Page 18 Issue 4 02/2002...
Page 291: Dc Charging Cable Pcc-1
PAMS Technical Documentation Service Tools DC Charging Cable PCC-1 The DC Cable PCC-1 is used e.g. to connect FLA-5/7 and TDF-4. Product Code DC Cable PCC-1 (with modular RJ connector): 0730053 View of PCC-1 E Nokia Corporation. Page 19 Issue 4 02/2002...
Page 292: Power Cable Pcs-1
The Power Cable PCS-1 is used to connect eg. Service Box JBU-6 and Flash Loading Adapter FLA-7 to an external power supply. Can be used with FPS-4 also. Product Code Power Cable PCS-1: 0730012 View of PCS-1 E Nokia Corporation. Page 20 Issue 4 02/2002...
Page 293: Dc Cable Scb-3
The DC Cable SCB-3 is used to connect the Service Battery to the char- ger connection Vin of the phone when doing the charger calibration ser- vice procedure. Product Code DC Cable SCB-3: 0730114 View of SCB-3 E Nokia Corporation. Page 21 Issue 4 02/2002...
Page 294: Service Cable Xms-3
NSM–3/3D PAMS Technical Documentation Service Tools Service Cable XMS-3 XMS-3 is a modular cable for flashing and service purposes. Product code Service Cable XMS-3: 0730174 View of XMS-3 E Nokia Corporation. Page 22 Issue 4 02/2002...
Page 295: Rf Cable Xrf-1
PAMS Technical Documentation Service Tools RF Cable XRF-1 RF cable XRF-1 is used to connect Test frame MJS-9 to RF measure- ment equipment.. Product code RF Cable XRF-1: 0730085 View of XRF-1 E Nokia Corporation. Page 23 Issue 4 02/2002...
Page 296: Rf Cable Xrs-3
PAMS Technical Documentation Service Tools RF Cable XRS-3 RF cable XRS-3 is used to connect Service Box JBU-6 to RF measure- ment equipment. Product code RF Cable XRS-3: 0730184 View of XRS-3 E Nokia Corporation. Page 24 Issue 4 02/2002...
Page 297: Modular T-Adapter
NSM–3/3D PAMS Technical Documentation Service Tools Modular T-adapter The modular T-adapter is a suitable branching unit to provide the needed parallel modular connections. Product Code Modular T-adapter: 4626134 View of Modular T-adapter E Nokia Corporation. Page 25 Issue 4 02/2002...
Page 298: Sw Security Device Pkd-1
Caution: Make sure thet you have switched off the PC and the printer before making connections! Caution: Do not connected the PKD-1 to the serial port. You may dam- age your PKD-1! Product Code SW Security Device PKD-1: 0750018 View of SW Security Device E Nokia Corporation. Page 26 Issue 4 02/2002...
Page 299: Dongle/Flash Device Fls-4S (Sales Pack)
Sales Pack - US 0080543 View of FLS-2D Sales Pack 0080543 Contents - US Part No. Description 0774283 FLS-4S Flash Device. 0680032 FPS–8 Power supply 9360406 Installation and User Guide 9385137 Registration Request Form E Nokia Corporation. Page 27 Issue 4 02/2002...
Page 300 NSM–3/3D PAMS Technical Documentation Service Tools This page intentionally left blank. E Nokia Corporation. Page 28 Issue 4 02/2002...
Page 301 PAMS Technical Documentation NSM–3/3D Series Transceivers Service Tools E Nokia Corporation. Issue 4 02/2002...
Page 302 ......... E Nokia Corporation.
Page 303 ..........E Nokia Corporation.
Page 304: Service Box Jbu-6
Product Code Service Box JBU-6: 0770153 View of JBU-6 SCD-6: Sales Package code: 0080329 Pinset Cable SCD-6: Spare part for JBU-6. RF Module RL6 for Service Box JBU-6 RF Module RL6: 0770172 E Nokia Corporation. Page 4 Issue 4 02/2002...
Page 305: Test Jig Mjs-9
See next page for additional info. Product Code Module Jig MJS-9: 0770154 View of MJS-9 *Note: The nominal supply voltage for MJS-9 is +8.0 V. The supply voltage must not exceed +15.0 V. (MJS-9 has overvoltage protection). E Nokia Corporation. Page 5 Issue 4 02/2002...
Page 306 Use LCD module CD9 when servicing with MJS-9. Product code: 0770244 Remove LCD/Keymat module from PCB before installing the radio module into the Service Jig MJS-9. Use LCD module CD9 0770244 instead of the original NSM-3 module. E Nokia Corporation. Page 6 Issue 4 02/2002...
Page 307: Soldering Jig Mjs-21
The Soldering Jig MJS-21 is used for soldering (in automatic soldering machines) and as a rework jig for system module, if special fixtures (like extra feet) are used. Product Code Module Jig MJS-21: 0770225 View of MJS-21 E Nokia Corporation. Page 7 Issue 4 02/2002...
Page 308: Flash Loading Adapter Fla-10
Sales package code Falsh Loading Adapter FLA-10: 0081346 Sales package contains: Falsh Loading Adapter FLA-10 (bulk) 0770229 DC Cable FLC-2 0730185 View of FLA-10 View of FLC-2 E Nokia Corporation. Page 8 Issue 4 02/2002...
Page 309: Battery Connector Extractor Tool Srt-3
Service Tools Battery Connector Extractor Tool SRT-3 The Battery Connector Extractor Tool is used to remove battery connector from the frame. Product Code Battery Connector Extractor Tool SRT-3: 0770226 View of SRT-3 E Nokia Corporation. Page 9 Issue 4 02/2002...
Page 310: Flash Loading Adapter Fla-7 (Sales Pack)
- Flash Loading Adapter FLA-7 0770119 - Service Cable XCM-5 0730142 - Power Cable SCF-7 0730141 - Service Cable assy AXS-5 0730091 Sales package code Flash Loading Adapter FLA-7: 0080326 View of FLA-7 E Nokia Corporation. Page 10 Issue 4 02/2002...
Page 311: Flash Prommer Fps-4S (Sales Pack)
AXS-4 cable D9-D9 0774043 Prommer software diskette Extension modules available : SF6 SRAM Extension module 0200742 SF7 FLASH Memory Extension module 0200743 Sales package code Flash Prommer FPS-4S: 0085095 View of FPS-4 E Nokia Corporation. Page 11 Issue 4 02/2002...
Page 312: Security Box Tdf-4
View of IR Data Interface Module JLP-1 IR Data Interface Module JLP-1 fits in the Security Box TDF-4 and can be used to perform IR tests with WinTesla. Product Code IR Data Interface Module JLP-1: 0750079 E Nokia Corporation. Page 12 Issue 4 02/2002...
Page 313: Product Code
1825019 Product Code Flash Battery BBF-1: 0775206 View of BBF-1 *Note: The nominal supply voltage for BBF-1 is +8.0 V. The supply voltage must not exceed +15.0 V. (BBF-1 has overvoltage protection). E Nokia Corporation. Page 13 Issue 4 02/2002...
Page 314 NSM–3/3D PAMS Technical Documentation Service Tools This page intentionally left blank. E Nokia Corporation. Page 14 Issue 4 02/2002...
Page 315: Service Cable Axs-4
The D9-D9 Service Cable AXS-4 is used to connect two 9 pin D connec- tors e.g. between PC and TDF-4 seurity box. Cable lenght is 2 meters. Product code D9-D9 Service Cable AXS-4 0730090 View of AXS-4 E Nokia Corporation. Page 15 Issue 4 02/2002...
Page 316: Service Cable Axs-4U
The D9-D9 Service Cable AXS-4U is used to connect two 9 pin D connec- tors e.g. between PC’s serial port and FLS-2D. Cable length is 30 cm. Product code D9-D9 Service Cable AXS-4U 0730163 View of AXS-4U E Nokia Corporation. Page 16 Issue 4 02/2002...
Page 317: D15-D15 Cable Axs-5
Service Tools D15-D15 Cable AXS-5 The D15-D15 Cable AXS-5 is used to connect two 15 pin D connectors. e.g. between FLA-5/7 and FPS-4S. Product Code D15-D15 Cable AXS-5: 0730091 View of AXS-5 E Nokia Corporation. Page 17 Issue 4 02/2002...
Page 318: Mbus Cable Dau-9S
MBUS Cable DAU-9S The MBUS Cable DAU-9S has a modular connector, and is used with be- tween PC’s serial port and eg. Service Box JBU-6. Product Code MBUS Cable DAU-9S: 0730108 View of DAU-9S E Nokia Corporation. Page 18 Issue 4 02/2002...
Page 319: Dc Charging Cable Pcc-1
PAMS Technical Documentation Service Tools DC Charging Cable PCC-1 The DC Cable PCC-1 is used e.g. to connect FLA-5/7 and TDF-4. Product Code DC Cable PCC-1 (with modular RJ connector): 0730053 View of PCC-1 E Nokia Corporation. Page 19 Issue 4 02/2002...
Page 320: Power Cable Pcs-1
The Power Cable PCS-1 is used to connect eg. Service Box JBU-6 and Flash Loading Adapter FLA-7 to an external power supply. Can be used with FPS-4 also. Product Code Power Cable PCS-1: 0730012 View of PCS-1 E Nokia Corporation. Page 20 Issue 4 02/2002...
Page 321: Dc Cable Scb-3
The DC Cable SCB-3 is used to connect the Service Battery to the char- ger connection Vin of the phone when doing the charger calibration ser- vice procedure. Product Code DC Cable SCB-3: 0730114 View of SCB-3 E Nokia Corporation. Page 21 Issue 4 02/2002...
Page 322: Service Cable Xms-3
NSM–3/3D PAMS Technical Documentation Service Tools Service Cable XMS-3 XMS-3 is a modular cable for flashing and service purposes. Product code Service Cable XMS-3: 0730174 View of XMS-3 E Nokia Corporation. Page 22 Issue 4 02/2002...
Page 323: Rf Cable Xrf-1
PAMS Technical Documentation Service Tools RF Cable XRF-1 RF cable XRF-1 is used to connect Test frame MJS-9 to RF measure- ment equipment.. Product code RF Cable XRF-1: 0730085 View of XRF-1 E Nokia Corporation. Page 23 Issue 4 02/2002...
Page 324: Rf Cable Xrs-3
PAMS Technical Documentation Service Tools RF Cable XRS-3 RF cable XRS-3 is used to connect Service Box JBU-6 to RF measure- ment equipment. Product code RF Cable XRS-3: 0730184 View of XRS-3 E Nokia Corporation. Page 24 Issue 4 02/2002...
Page 325: Modular T-Adapter
NSM–3/3D PAMS Technical Documentation Service Tools Modular T-adapter The modular T-adapter is a suitable branching unit to provide the needed parallel modular connections. Product Code Modular T-adapter: 4626134 View of Modular T-adapter E Nokia Corporation. Page 25 Issue 4 02/2002...
Page 326: Sw Security Device Pkd-1
Caution: Make sure thet you have switched off the PC and the printer before making connections! Caution: Do not connected the PKD-1 to the serial port. You may dam- age your PKD-1! Product Code SW Security Device PKD-1: 0750018 View of SW Security Device E Nokia Corporation. Page 26 Issue 4 02/2002...
Page 327: Dongle/Flash Device Fls-4S (Sales Pack)
Sales Pack - US 0080543 View of FLS-2D Sales Pack 0080543 Contents - US Part No. Description 0774283 FLS-4S Flash Device. 0680032 FPS–8 Power supply 9360406 Installation and User Guide 9385137 Registration Request Form E Nokia Corporation. Page 27 Issue 4 02/2002...
Page 328 NSM–3/3D PAMS Technical Documentation Service Tools This page intentionally left blank. E Nokia Corporation. Page 28 Issue 4 02/2002...
Page 329 PAMS Technical Documentation NSM–3/3D Series Transceivers Non Serviceable Accessories E Nokia Mobile Phones Ltd. Issue 3 11/2000...
Page 330 ........E Nokia Mobile Phones Ltd.
Page 331: Standard Battery Blb-2
NSM–3/3D PAMS Technical Documentation Non Serviceable Accessories Standard Battery BLB–2 The BLB–2 is a Li–ion battery with 650 mAh capacity in white plastic package. Product Code Battery pack BLB–2: 0670246 E Nokia Mobile Phones Ltd. Page 3 Issue 3 11/2000...
Page 332: Ac Travel Charger Acp-7
(UK plug) 180–220 Vac AC Travel Charger ACP–7A 0675148 (Australia) 216–264 Vac Specification 3.5 mm DC plug, 2–pole Output connectors: Protection: PTC protection Output Voltage /Current (typ) 7.6 V / 370 mA E Nokia Mobile Phones Ltd. Page 4 Issue 3 11/2000...
Page 333: Performance Travel Charger Acp-8
Australia plug 90–264 Vac Specification Output connectors: 3.5 mm DC plug, 2–pole (+, –, control) Protection: Output fault voltage 16 V max. Output voltage/current (typ): 6.0 V ( 0.3 V) / 620 mA E Nokia Mobile Phones Ltd. Page 5 Issue 3 11/2000...
Page 334: Desktop Stand Dcv-1B
Non Serviceable Accessories Desktop Stand DCV–1B The desktop stand provides mounting place for charging battery with transceiver. Product Code Desktop stand DCV–1B: 0675220 Specification Connections: 3.5 mm DC jack (ACP–7 or ACP–8) E Nokia Mobile Phones Ltd. Page 6 Issue 3 11/2000...
Page 335: Cigarette Lighter Charger Lch-8
Output connectors: 3.5 mm DC plug, 3 pin. Protection: input fused, output current limit 650 mA Voltage 10.8...32 V input: output: The output voltage is controlled by the phone via 3:rd wire. E Nokia Mobile Phones Ltd. Page 7 Issue 3 11/2000...
Page 336: Cigarette Lighter Charger Lch-9
D 21/23 mm output: 3.5 mm DC plug input fused, output current limit 850 mA Protection: Voltage input: 11...32 V output (nominal): 8.4 V 800 mA Nominal output current: E Nokia Mobile Phones Ltd. Page 8 Issue 3 11/2000...
Page 337: Plug And Play Hands Free Cigarette Charger Pph-1
Product Code 0675182 Headset PPH–1: Specification Output connectors: 3.5 mm DC plug, 2–pole (+, –, control) Intput voltage: 8–16VDC Protection: Output fault voltage 16 V max. Output current: 750 mA max. E Nokia Mobile Phones Ltd. Page 9 Issue 3 11/2000...
Page 338: Handsfree Microphone Hfm-8
NSM–3/3D PAMS Technical Documentation Non Serviceable Accessories Handsfree Microphone HFM–8 The HFM–8 microphone can be used together with PPH–1 plug and play handsfree unit. Product Code Handsfree microphone HFM–8: 0690016 E Nokia Mobile Phones Ltd. Page 10 Issue 3 11/2000...
Page 339: Headset Hdc-5
NSM–3/3D PAMS Technical Documentation Non Serviceable Accessories Headset HDC–5 The HDC–5 headset provides a also hook switch for the phone/micro- phone. Product Code Headset HDC–5: 0694059 E Nokia Mobile Phones Ltd. Page 11 Issue 3 11/2000...
Page 340: Loopset Lps-3
Note (1): The capacity of the zinc air battery will fall 20% in a month. After the activation the zinc air battery begins to self–discharge. The battery will be empty within 5 weeks. E Nokia Mobile Phones Ltd. Page 12 Issue 3 11/2000...
Page 341: Pocket Clip Skb-2
Product Code Pocket Clip SKB–2: 0720218 Package includes: Button for SKB–2 3 pcs Screw 3 pcs Mounting rubber for SKB–2 3 pcs Pocket Clip SKB–2 1 pc Button for SKB–2 E Nokia Mobile Phones Ltd. Page 13 Issue 3 11/2000...
Page 342: Swivel Mount Hhs-12
PAMS Technical Documentation Non Serviceable Accessories Swivel Mount HHS–12 The HHS–12 Swivel Mount is a mount that allows the Pocket clip SKB–2 to be adjusted. Product Code Swivel Mount HHS–12: 0620054 E Nokia Mobile Phones Ltd. Page 14 Issue 3 11/2000...

This manual is also suitable for:

Nsm–3d

Nokia NSM–3 Service Manual

Pams Technical Documentation Nsm-3/3D Series Transceivers

Nsm-3/3D Series Transceivers

Pams Technical Documentation Nsm-3/3D Series Transceivers

Pams Technical Documentation Nsm-3/3D Series Transceivers

Pams Technical Documentation Nsm-3/3D Series Transceivers

Pams Technical Documentation Nsm-3/3D Series Transceivers

Pams Technical Documentation Nsm-3/3D Series Transceivers

Quick Links

Chapters

Related Manuals for Nokia NSM–3

Summary of Contents for Nokia NSM–3