Federal Communications Commission IrDA Infrared Data Association IrMC Infrared Mobile Communications IrOBEX IrDA Object Exchange Protocol Interim Standard Intelligent Software Architecture Liquid Crystal Display Light Emitting Diode Micro Control Unit / Master Control Unit Nokia Corporation Issue 2 09/2003 Confidential Page 7...
Page 8
TDMA Time Division Multiple Access. Here: US digital cellular system. Telecommunications Industry Association Teletype Universal Energy Management, a Baseband ASIC. Universal Phone Processor, a Baseband ASIC. VCTCXOVoltage Controlled temperature Compensated Crystal Oscillator Wireless Application Protocol (Browser) Nokia Corporation Page 8 Confidential Issue 2 09/2003...
RH-41 CCS Technical Documentation System Module Transceiver RH-41 (Nokia 2260) Introduction The RH-41 is a dual band transceiver unit designed for TDMA800/1900 networks. The transceiver consists of the engine module (ST6_11) and the various assembly parts. The transceiver has a full graphic display and the user interface is based on a Jack style UI with two soft keys.
Iq-mode when in the Sleep mode. The VIO regulator supplies both the external and internal logic circuitries. It is used by the LCD, flash and UPP. The regulator goes into the low Iq-mode when in the Sleep mode. Nokia Corporation Page 12 Confidential...
(Not used in RH-41). In addition to these, external components are needed for EMC protection of the charger input to the baseband module. Digital Interface Data transmission between the UEM and the UPP is implemented using two serial con- Nokia Corporation Issue 2 09/2003 Confidential Page 13...
Pin 3 (Vss9) is the LCD driver’s ground and Pin 9 (GND) is used to ground the metal frame. Keyboard Introduction The RH-41 keyboard style follows the Nokia Jack style, without side keys for volume con- trol. The PWR key is located at the top of the phone. Nokia Corporation Issue 2 09/2003...
The S-line S0 and R-line R5 are not used at all. Returns / Scans Send Soft left Down Soft right where NC = Not Connected Nokia Corporation Page 16 Confidential Issue 2 09/2003...
Because of the FET, the microphone needs a bias voltage. Buzzer Introduction The operating principle of the buzzer is magnetic. The diaphragm of the buzzer is made Nokia Corporation Issue 2 09/2003 Confidential Page 17...
The voltage seen in the outer terminals is zero (or float- ing), and the battery is activated by connecting the charger. The battery has internal pro- tection for overvoltage and overcurrent. Nokia Corporation Page 18 Confidential...
The interface is supported by fully differential 4-wire (XMICN, XMICP, XEARN, and XEARP) accessories. RH-41 supports the HDE-2 inbox headset, HDB-5 Boom headset, HDC-5 headset, LPS-3 loopset, and the PPH-1 car kit. Nokia Corporation Issue 2 09/2003 Confidential Page 19...
Page 20
UEM. The HOOKINT- interrupt is generated by the button in the headset or by the acces- sory external audio input. 2.7V Hookint /MBUS Headint Headint 2.1V MIC1Bias 1.8V MIC1P MIC1N 0.3V MicGND 0.8V 3...25k HFCM 100p Figure 7: Accessory Detection / External Audio Nokia Corporation Page 20 Confidential Issue 2 09/2003...
V100 protects the UEM ASIC from reverse-polarity charging voltage and from too-high charging voltages. C106 is also used for ESD and EMC protection. Spark gaps right after the charger plug are used for ESD protection. Nokia Corporation Issue 2 09/2003 Confidential...
F B U S R X M B U S T X M B U S R X U P P ( D 4 0 0 ) Figure 10: Test points located between UEM and UPP Nokia Corporation Page 22 Confidential Issue 2 09/2003...
PWB. The microphone is an asymmetrical circuit, which makes it well protected against EMC. EARP The EARP is protected with C-cover metallization and with a plastic-fronted earpiece. Buzzer PWB openings with the C-cover metallization protect the buzzer from ESD. Nokia Corporation Issue 2 09/2003 Confidential Page 23...
All the signal descriptions and properties in the following tables are valid only for active signals, and the signals are not necessarily present all the time. Note: In the following tables, the nominal signal level of 2.78V is sometimes referred to as 2.7V . Nokia Corporation Page 24 Confidential...
The RH-41 frequency plan is shown in the following figure. A 19.44 MHz VCTCXO is used for UHF and VHF PLLs and as a baseband clock signal. All RF locals are generated in PLLs. Nokia Corporation Issue 2 09/2003 Confidential...
Note: The current values in the following figure are not absolute values and cannot be measured. These values represent maximum/typical currents drawn by the corresponding RF or Taco blocks in use, and are, therefore, dependent on the phone’s operating mode and state. Nokia Corporation Page 42 Confidential...
REF_in + PLLs VCC_DIGI 50 uA VREFRF01 bias reference VREF VBATT 3.1-5.0 V Figure 12: Power distribution Regulators The regulator circuit is the UEM and the specifications can be found in the following table: Nokia Corporation Issue 2 09/2003 Confidential Page 43...
The local signal's partition to receiver selectivity and IMD depends then mainly on the spectral purity of the 1st local. Zero 2nd IF stages include most of receiv- ers signal gain, AGC control range and channel filtering. Nokia Corporation Page 44 Confidential...
Page 45
1st IF gain control range, AGC 2 step R X 2nd IF gain control range, 8x6dB steps Min signal level at RX-ADC input @ sensitivity digital analog Input dynamic range -116... -20 Nokia Corporation Issue 2 09/2003 Confidential Page 45...
LNA has good linearity, still low noise figure and about -3 dB gain. During TX slot LNA is in power-down mode, which is executed by switching the bias cur- rent source to 0 mA. Nokia Corporation Page 46 Confidential...
Page 47
Min voltage gain, Mixer + 2nd IF (IF+2nd AGC min.) Gain charge, dB, temp Mixer+2nd IF -30...+85 C IQ mixers + AMP2 RF input impedance differential kohm/pF RF input frequency range 135.54 Nokia Corporation Issue 2 09/2003 Confidential Page 47...
TX VHF Synthesizer includes integrated PLL, loop filter, and resonator. The output of TX-VHF PLL is used as a LO signal for the IQ-modulator of the transmitter. See depicted block diagrams and synthesizer characteristics from synthesizer Nokia Corporation Page 48 Confidential...
The input and return losses are about –10dB. Power amplifier is 50Ω/50Ω module. It does not have own enable/disable control signal, but it can be enabled by bias voltage and reference bias current signals. The gain window Nokia Corporation Issue 2 09/2003 Confidential...
The output power tuning target for power level 2 after diplexer (or after switch for exter- nal RF) is +27.3dBm for digital modes and +24.8 dBm for analog mode. See the following table. Modulation accuracy and ACP will be within limits specified in IS-136/137. Nokia Corporation Page 50 Confidential...
The RH-41 antenna solution is an internal, dual-resonance PIFA. This antenna has a com- mon feeding point for both antenna radiators, which results in the need for a diplexer. In a single band transceiver, an SMD-compatible through-chip can be used. Nokia Corporation Issue 2 09/2003 Confidential...